网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
In （） pumps a closed discharge valve will cause bursting discharge pressure.
A
centrifugal
B
plunger
C
injector
D
water
参考答案
参考解析
解析：
暂无解析
更多 “单选题In （） pumps a closed discharge valve will cause bursting discharge pressure.A centrifugalB plungerC injectorD water” 相关考题
考题
A cargo hose is marked with the ______．A.maximum working pressureB.bursting pressureC.safety relief valve settingD.maximum temperature
考题
Before discharge of cargo tank ballast is undertaken，______．A.the deck isolating valve is openB.flue gas isolating valveC.blower suction valveD.blower discharge valve
考题
To ensure proper seating when closing a valve on a tank，the valve should be ______．A.Set up as tight as possible by handB.Set up tight using a valve wrenchC.Closed，opened a half turn，and then closedD.Closed against the stop and the locking pin inserted
考题
单选题In （） pump a closed discharge valve will not cause excessive pressure to build up.A
gearB
vaneC
screwD
centrifugal
考题
单选题Petroleum cargo tanks should not be topped off at deck level when loading on a cold day because（）.A
a subsequent temperature rise will cause the cargo to overflowB
air pockets may cause the cargo to bubble out of the ullage holeC
the increased viscosity of the product requires higher loading pressure which increases the chances of a spillD
the tank valve may be stiff and a spill will occur before the valve can be closed
考题
单选题What is a function of the wearing rings used in most centrifugal pumps?（）A
Absorb erosion of high velocity discharge streamB
Seal pump shaft against entry of airC
Isolate the discharge side from the suction sideD
Dampen the turbulent discharge flow
考题
单选题Gear pumps are of positive displacement type pumps because they discharge a near constant amount of liquid （） pressure.A
depending onB
in relative toC
regardless ofD
because of
考题
单选题If a centrifugal bilge pump were continually operated with the discharge valve closed the （）.A
motor overload would openB
relief valve would openC
pump would eventually overheatD
motor would overheat
考题
单选题Which of the following statements represents the advantage of rotary pumps as compared to reciprocating pumps?（）A
The high discharge pressure of the rotary pumps permits a larger volume of fluid per unit time than the reciprocating pumpB
Rotary pumps are capable of pumping more fluid than reciprocating pumps of the same weightC
Rotary pumps occupy only one-half the space of reciprocating pumpsD
Rotary pumps eliminate discharge slippage of the pumped liquid, while this does not hold true for a reciprocating pump
考题
单选题What is a characteristic of all centrifugal cargo pumps? （）A
They are self-primingB
Decreasing the speed of rotation will decrease the discharge pressureC
Opening the discharge valve wider will increase the discharge pressureD
All of the above
考题
单选题Most pump manufacturers recommended that the discharge piping for centrifugal pumps be （）.A
one size larger than the pump discharge nozzleB
the same size as the pump discharge nozzleC
one size smaller than the pump discharge nozzleD
installed with a short radius elbow at the pump
考题
单选题Which of the following pumps will build up a bursting pressure or stall their motors if the discharge valves are closed?（） (1) gear (2) centrifugal (3) screwA
（1）and（2）B
（1），（2）and（3）C
（1）and（3）D
（2）and（3）
考题
单选题Which of the following statements is true concerning centrifugal pumps?（）A
They are particularly suited for pumping high viscosity fluidsB
They are started with the discharge valve openedC
The flow of liquid is developed by imparting energy due to the rotation of an impellerD
They are always mounted in a horizontal position
考题
单选题Which of the following problems could cause air to blow out through the inlet air filter of a running compressor?（）A
Excessive compression in the cylinderB
A broken intake valveC
A dirty inlet filter elementD
An improperly adjusted discharge valve
考题
单选题Why is it important for fuel oil tanks not to be topped off at the inner bottom level when loading on a cold day?（）A
Increased viscosity of the product needs higher loading pressure, which increases the chances of a spillB
Air pockets may cause the fuel to bubble out of the ullage holeC
The temperature rise of the fuel will cause an overflowD
Fueling valve may become stuck closed and cause the fuel oil to spill before the valve can be opened
考题
单选题Which of the listed statements is correct concerning the starting of centrifugal pumps?（）A
They should always be started with the discharge valve closedB
They should always be started with the discharge valve openedC
A priming pump is always required to flood the impeller suctionD
They should always be started with the sealing line valves closed
考题
单选题A relief valve for a cargo pump is generally installed（）.A
after the discharge valveB
between the pump and discharge valveC
after the suction valveD
between the pump and suction valve
考题
单选题One of the reasons that cause oil flowed from sludge outlet of a self-cleaning separator is（）A
seal water supply be cut offB
make up water supply be cut offC
oil outlet valve closed or not open sufficientlyD
the flow rate of oily water is too much
考题
单选题If a centrifugal pump were continually operated with the discharge valve closed, the （）.A
motor controller overload would openB
pump would eventually overheatC
relief valve would continuously cycle openD
motor would overheat
考题
单选题The valve on the discharge side of a cargo pump on a tanker will usually be a（）.A
butterfly valveB
spectacle valveC
check valveD
globe valve
考题
单选题One of the consequences in continuing to operate a centrifugal bilge pump with the discharge valve closed, is that the （）.A
motor overload will openB
relief valve will openC
pump will overheatD
motor will overheat
考题
单选题A centrifugal pump attempting to develop flow against a closed discharge valve has a/an （）.A
capacity of 0%B
efficiency of 100%C
internal slippage of 0%D
shut off horsepower rating of 100%
考题
单选题If an operating bilge pump is developing good vacuum, but is unable to discharge any water, which of the following problems is the most probable cause?（）A
The wearing rings are excessively wornB
The suction strainer is cloggedC
The discharge valve is cloggedD
The shaft is worn
考题
单选题The major difference between the discharge and suction valves installed in most low pressure, reciprocating air compressors is that（）A
one valve seats upwards, while the other seats downwardsB
the reed valves used on the discharge are made substantially thicker and heavier than the suction valvesC
the suction valve springs exert a greater tension than the discharge valve springsD
the discharge valve springs exert a greater tension than the suction valve springs
考题
单选题If the discharge valve is closed before the drive motor is stopped, which of the following types of pumps will most likely be damaged?（）A
CentrifugalB
GearC
PropellerD
Turbine
考题
单选题The valve on the discharge side of a cargo pump on a tank vessel will usually be a（）.A
butterfly valveB
spectacle valveC
check valveD
globe valve
热门标签
最新试卷