网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）
- A、The switches are not stackable
- B、The cable was not wired using 568A
- C、The cable needs to be a crossover cable
- D、The switches have IGMP snooping enabled
参考答案
更多 “ A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）A、The switches are not stackableB、The cable was not wired using 568AC、The cable needs to be a crossover cableD、The switches have IGMP snooping enabled” 相关考题
考题
A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch.Which of the following settings on the switch will need to be configured to support the printer?（）A. MAC filteringB. IP addressC. PoED. Port speed
考题
A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?()
A.StraightB.ConsoleC.CrossoverD.Loopback
考题
An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?()
A. Battery needs to be replacedB. Light switch is turned offC. Smart cable is disconnectedD. UPS needs a firmware update
考题
The Ezonexam network administrator needs to a switch named VE1 to become the root bridge for a redundant path switched network. What can be done to ensure that VE1 will always assume the role as the root bridge?A．Assign the switch a higher MAC address than the other switches in the network haveB．Establish a direct link from the switch to all other switches in the networkC．Configure the switch full-duplex operation and configure the other switches for half-duplex operationD．Configure the switch so that it has lower priority than other switches in the networkE．None of the above
考题
A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?()
A. The switch port link lights will be off on both switches indicating the ports are not connected.B. The switch port link light will be off on one switch indicating that STP has disabled the port.C. The switch port link lights will flash amber indicating an error.D. The switch port link lights will be green indicating normal operation.
考题
A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration?()
A. A switch in the VTP client mode cannot update its local VLAN database.B. A trunk link must be configured between the switches to forward VTP updates.C. A switch in the VTP server mode can update a switch in the VTP transparent mode.D. A switch in the VTP transparent mode will forward updates that it receives to other switches.E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.
考题
A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。A.Establish a direct link from the switch to all other switches in the network.B.Assign the switch a higher MAC address than the other switches in the network have.C.Configure the switch so that it has a lower priority than other switches in the network.D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.E.Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
考题
While troubleshooting a network connectivity problem, a technician observes steady link lights on both the workstation NIC and the switch port to which the workstation is connected. However, when the ping command is issued from the workstation, the output message "Request timed out." is displayed. At which layer of the OSI model does the problem most likely exist（）。A.the session layerB.the protocol layerC.the data link layerD.the access layerE.the network layerF.the application layer
考题
A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?（）A、StraightB、ConsoleC、CrossoverD、Loopback
考题
A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）A、The switch port link lights will be off on both switches indicating the ports are not connected.B、The switch port link light will be off on one switch indicating that STP has disabled the port.C、The switch port link lights will flash amber indicating an error.D、The switch port link lights will be green indicating normal operation.
考题
A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch. Which of the following settings on the switch will need to be configured to support the printer?（）A、MAC filteringB、IP addressC、PoED、Port speed
考题
A technician is troubleshooting a laptop LCD, and when the cover is opened nothing shows on the screen. Then all of a sudden the screen comes on and works fine. Which of the following should the technician check FIRST?（）A、BacklightB、InverterC、Loose cableD、Lid switch
考题
While troubleshooting a network connectivity problem, a technician observes steady link lights on both the workstation NIC and the switch port to which the workstation is connected. However, when the ping command is issued from the workstation, the output message "Request timed out." is displayed. At which layer of the OSI model does the problem most likely exist（）。A、the session layerB、the protocol layerC、the data link layerD、the access layerE、the network layerF、the application layer
考题
A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）A、The wrong cable type has been used.B、. IDS has shut down the computer's switch port.C、The port on the switch is configured incorrectlyD、Spanning tree protocol was implemented.
考题
A network administrator needs to add an additional connection to a room. The administrator adds a new Ethernet switch and must connect it to an existing switch. Which cable type should be used to connect the two switches?（）A、CAT3 cableB、Serial cableC、Crossover cableD、Rollover cable
考题
A user is unable to connect to the network. A network technician is able to determine that there is a problem on the switch. All other users on that switch are able to connect successfully to the network. Which of the following is a probable cause？（）A、Switching loop is occurring on the switch.B、Wrong subnet mask on the switch.C、Incorrect SNMP settings on the switch.D、Port is misconfigured on the switch.
考题
An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot. Which of the following is the FIRST thing the administrator should check？（）A、 Default gatewayB、 The ports on the switchC、 Port security on the servers switch portD、 Ethernet cable
考题
A technician needs to find an end of a network cable drop. Which of the following tools would the technician use?（）A、Cable testerB、MultimeterC、Toner probeD、Loopback plug
考题
An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?（）A、Battery needs to be replacedB、Light switch is turned offC、Smart cable is disconnectedD、UPS needs a firmware update
考题
When testing a CAT5 cable, the technician notices that pin A is open. However, the cable stillworks fine. Which of the following describes how this is possible?（）A、The cable was tested for 100Base-TX.B、The cable is a 1000BaseT cable.C、The switch uses link aggregation,D、The switch was setup to use MDIX
考题
A user has just moved a PC from one office to another. The patch cable and the NIC do notappear to be functioning in the new office but were working before the move. The patch cable is plugged in correctly to both the NIC and the wall jack. Which of the following actions should the technician take FIRST?（）A、Verify that the network card is compatible with the operating system.B、Verify that the port on the switch is enabled.C、Update the network card driver.D、Replace the network cable with a crossover cable.
考题
单选题A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）A
The switches are not stackableB
The cable was not wired using 568AC
The cable needs to be a crossover cableD
The switches have IGMP snooping enabled
考题
单选题A technician needs to find an end of a network cable drop. Which of the following tools would the technician use?（）A
Cable testerB
MultimeterC
Toner probeD
Loopback plug
考题
单选题A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）A
The wrong cable type has been used.B
. IDS has shut down the computer's switch port.C
The port on the switch is configured incorrectlyD
Spanning tree protocol was implemented.
考题
单选题A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）A
The switches are not stackableB
The cable was not wired using 568AC
The cable needs to be a crossover cableD
The switches have IGMP snooping enabled
考题
单选题When testing a CAT5 cable, the technician notices that pin A is open. However, the cable stillworks fine. Which of the following describes how this is possible?（）A
The cable was tested for 100Base-TX.B
The cable is a 1000BaseT cable.C
The switch uses link aggregation,D
The switch was setup to use MDIX
考题
单选题An administrator has a malfunctioning uninterruptible power supply （UPS）. Which of the following is the MOST likely cause of the problem？（）A
Battery needs to be replacedB
Light switch is turned offC
Smart cable is disconnectedD
UPS needs a firmware update
热门标签
最新试卷