网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
（）can not cause oil flow from water outlet of self-cleaning separator.
A
Oil temperature too high
B
Diameter of gravity disc too large
C
Oil temperature too low
D
High level tank out of water
参考答案
参考解析
解析：
暂无解析
更多 “单选题（）can not cause oil flow from water outlet of self-cleaning separator.A Oil temperature too highB Diameter of gravity disc too largeC Oil temperature too lowD High level tank out of water” 相关考题
考题
One of the reasons that causes oil flowed from sludge outlet of a self-cleaning purifier isA.seal water supply be cut offB.make-up water supply be cut offC.oil outlet valve closed or not open sufficientlyD.the flow rate of oil is too much
考题
第二组The only attention that heat exchanger should require is to ensure that the heat transfer surfaces remain substantially clean and the flow passages generally clear of obstruction. Indication that undue fouling is occurring is given by a progressive increase in the temperature difference between the two fluids, over a period of time, usually accompanied by a noticeable rise in pressure loss at a given flow.Fouling on the sea-water side is the most usual cause of deterioration in performance. The method of cleaning the sea water-side surfaces depends on the type of heat exchanger. With shell-and-tube heat exchangers, the removal of the header covers or, m the case of the smaller heat exchangers, the headers themselves, will provide access to the tubes. Obstructions, dirt, scale etc., can then be removed, using the tools provided by the heat exchanger manufacturer. Flushing through with fresh water is recommended before a heat exchanger is returned to service. In some applications, such as piston oil cooling, progressive fouling may take place on the outside of the tubes. Most manufactures recommend a chemical flushing pr6cess to remove this in situ~ without dismantling the heat exchanger.Plate heat exchangers may be cleaned by unclamping the stack of plates and mechanically cleaning the surface of each plate as recommended by the manufacturers. The plate seals may require replacement from time to time and here the manufacturers instructions should be closely followedBy which of the following indication, can we conclude that the lube oil-sea water heat exchanger is unduly fouled?A.the heat exchanger lube oil inlet temperature loweringB.the heat exchanger sea-water outlet pressure riseC.the heat exchanger temperature difference between lube oil and sea water increasingD.the heat exchanger pressure difference between sea water inlet and outlet decreasing
考题
_______can cause oil flow from water outlet of the oil purifier.A.Oil inlet valve opening too quicklyB.Oil temperature little higher than normalC.Diameter of gravity disc too smallD.Viscosity of oil little lower than normal
考题
Before loading bulk grain, bilge wells must be covered to ______.A.add strength to the bilge well strainerB.permit rapid flow of water to the bilge wellsC.prevent cargo sifting into the bilge wellsD.prevent oil, water, or other liquid from reaching the cargo
考题
单选题（）can be used to prevent hydraulic system overloaded or keep the pressure of oil outlet from pump constant.A
Overflow valveB
Reducing valveC
Balancing valveD
Reducing valve or balancing valve
考题
单选题If the cooling water temperature and the lube oil temperature in a diesel engine are too high, the cause can be （）A
a dirty lube oil strainerB
internal water leaksC
an oil suction line restrictionD
excessive wears of the cooling water pump
考题
单选题A dirty fuel oil filter element can be detected by （）A
Visual inspection of the elementB
the pressure drop cross the filterC
high fuel oil tank temperatureD
increase flow rate from the filter
考题
单选题Black smoke coming from a boiler can be caused by （）.A
low water levelB
high water levelC
excessively high fuel pressureD
low oil temperature
考题
单选题The three conditions which cause engine shutdown are overspeed，low lube oil pressure，and（）.A
High lube oil pressureB
High jacket water pressureC
High jacket water temperatureD
Low jacket water pressure
考题
单选题Before loading bulk grain，bilge wells must be covered to（）.A
add strength to the bilge well strainerB
permit rapid flow of water to the bilge wellsC
prevent cargo sifting into the bilge wellsD
prevent oil，water，or other liquid from reaching the cargo
考题
单选题White smoke exhausting from a diesel engine can result from （）A
high exhaust temperatureB
high lube oil temperatureC
low turbo-charger speedD
low cooling water temperature
考题
单选题The （） of the gravity disc is too big It causes oil to flow through the water outletWe changed the disc and no oil is found in the water outlet.A
gravityB
diameterC
circumferenceD
cylinder
考题
单选题（）can cause oil flow from water outlet of a separator.A
Oil inlet valve opening too quicklyB
Oil temperature too highC
Diameter of gravity disc too smallD
Viscosity of oil too low
考题
单选题The diameter of the gravity disc is too big It causes oil to flow through the water outlet We changed the disc and no （） is found in the water outlet.A
waterB
oilC
scaleD
ridge
考题
单选题A diesel engine fails to start due to excessive water in the fuelBefore the engine can be started, the water should be removed from the（）A
fuel linesB
lube oil filterC
crank case pumpD
rocker arm reservoir
考题
单选题Which of the following conditions indicates the dilution of diesel engine lube oil by fuel oil?（）A
Water discharging from the water outlet of the lube oil purifierB
Fuel oil discharging from the water outlet of the lube oil purifierC
Lube oil discharging from the water outlet of the lube oil purifierD
A change in the lube oil viscosity
考题
单选题When finish work on the oil separator, you should（）firstly.A
cut off the powerB
cut off the oil inletC
open guide water valveD
close oil outlet value
考题
单选题The outlet from an expansion tank of a closed freshwater cooling system should be piped to the （）.A
cylinder head water outlet headerB
cylinder jacket inlet mainC
heat exchanger inlet connectionD
jacket water pump suction line
考题
单选题In a four-stroke/cycle diesel engine, badly worn intake valve guides can cause excessive（）.A
exhaust pressureB
exhaust temperaturesC
cooling water temperaturesD
lube oil consumption
考题
单选题（）can cause oil flow from sludge outlet of self cleaning separator.A
Too much sludge accumulated in separator bowlB
Diameter of gravity disc too largeC
High level tank lack of waterD
Oil input too rapidly
考题
单选题（）can not cause oil flow from water outlet of self-cleaning separator.A
Oil temperature too highB
Diameter of gravity disc too largeC
Oil temperature too lowD
High level tank out of water
考题
单选题One cause of high head pressure occurring in a refrigeration system can be （）.A
insufficient cooling water flow to the condenserB
a low refrigerant charge in the systemC
the liquid valve is open too muchD
high evaporator superheat
考题
单选题Which of the following statements is true concerning an oil cooler?（）A
The oil temperature is less than the cooling water temperatureB
The oil pressure is less than the cooling water pressureC
The oil pressure is greater than the cooling water pressureD
The oil flow control valve is always installed in the oil input line
考题
单选题For a L√Opurifier, if the back pressure of the oil outlet is too high, the interface between oil and water in the bowl will （）.A
be interruptedB
move downwardsC
move outwardsD
retain original position
考题
单选题One of the reasons that cause oil flowed from sludge outlet of a self-cleaning separator is（）A
seal water supply be cut offB
make up water supply be cut offC
oil outlet valve closed or not open sufficientlyD
the flow rate of oily water is too much
考题
单选题One of the reasons that causes oil flowed from sludge outlet of a self-cleaning purifier is （）A
seal water supply be cut offB
make-up water supply be cut offC
oil outlet valve closed or not open sufficientlyD
the flow rate of oil is too much
考题
单选题Just after stopping the engine while the oil is still circulating.Check that uniform oil jets appear from all the oil outlet grooves in the crosshead bearing lower shell and the guide shoes.The oil flow from （） must be compared from unit; there should be a similarity in the flow patterns.A
the piston cooling oil return pipesB
the main and crankpin bearingsC
thrust and intermediate bearingsD
stern tube and thrust bearings
考题
单选题Which of the listed failures, occurring in an automated diesel generator system, should cause an audible alarm at the engine room control station?（）A
Low cooling water outlet temperatureB
High lube oil pressureC
Low lube oil temperatureD
Low starting air pressure
热门标签
最新试卷