网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0".Whic h of the following is most likely to have caused this output to occur on R1?（）
A. R1 has been configured with an ip default- network 2.0.0.0 command.
B. R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.
C. R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
D. Another router has been configured with an ip default - network 2.0.0.0 command.
E. Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
参考答案
更多 “ Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: Gateway of last resort is 1.1.1.1 to network 2.0.0.0.Whic h of the following is most likely to have caused this output to occur on R1?（）A. R1 has been configured with an ip default- network 2.0.0.0 command.B. R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C. R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D. Another router has been configured with an ip default - network 2.0.0.0 command.E. Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command. ” 相关考题
考题
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
考题
A network design shows that R1 has four different possible paths from itself to the Data Center subnets.Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）A. show ip eigrp topologyB. show ip eigrp topology all - linksC. show ip route eigrpD. show ip route eigrp all - linksE. show ip eigrp topology all - learned
考题
Refer to the exhibit. BigBids Incorporated is a worldwide auction provider. The network uses EIGRP as its routing protocol throughout the corporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all - links command, answer the administrator‘s questions.Which three networks is the router at 172.17.10.2 directly connected to?（）A. 172.17.0.0/30B. 172.17.1.0/24C. 172.17.2.0/24D. 172.17.3 .0/25E. 172.17.3.128/25F. 172.17.10.0/24
考题
TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?（）A. TestKing# show eigrp entriesB. TestKing# show protocolsC. TestKing# debug eigrp routesD. TestKing# show ip route eigrpE. TestKing# show route eigrp
考题
Which command will display all the EIGRP feasible successor routes known to a router?()
A. Router# show ip eigrp routes *B. Router# show ip eigrp summaryC. Router# show ip eigrp topologyD. Router# show ip eigrp adjacenciesE. Router# show ip eigrp neighbors detail
考题
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?()
A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
考题
A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）A. Router# show ip eigrp adjacencyB. Router# show ip eigrp topologyC. Router# show ip eigrp interfacesD. Router# show ip eigrp neighbors
考题
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192／26 network to a host on the LAN attached to router R1?()
A.The path of the packets will be R3 to R2 to R1.B.The path of the packets will be R3 to R1 to R2.C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.D.The path of the packets will be R3 to R1
考题
TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?（）A、TestKing# show eigrp entriesB、TestKing# show protocolsC、TestKing# debug eigrp routesD、TestKing# show ip route eigrpE、TestKing# show route eigrp
考题
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A、show ip routeB、show ip eigrp topologyC、show ip ospf topologyD、show ip eigrp topology 10.1.1.0/24
考题
EIGRP uses five generic packet types （hello， updates， queries， replies， acknowledgements）. If youwished to view the statistics for these packets， which IOS command should you use？（）A、debug eigrp packetsB、show ip eigrp trafficC、show ip eigrp topologyD、show ip eigrp neighbors
考题
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（） Network Next Hop Metric LocPrf Weight Path * 3.3.3.3 0 0 1 1 1 1 2 18 iA、The Enterprise likely uses ASN 1.B、The neighboring ISP likely uses ASN 1.C、The route has been advertised through ASN 1 multiple times.D、Router Ent1 will add another ASN to the AS_Path before advertising this route to its iBGP peer (4.4.4.4).
考题
Which command will display all the EIGRP feasible successor routes known to a router?（）A、Router# show ip eigrp routes *B、Router# show ip eigrp summaryC、Router# show ip eigrp topologyD、Router# show ip eigrp adjacenciesE、Router# show ip eigrp neighbors detail
考题
A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）A、Router# show ip eigrp adjacencyB、Router# show ip eigrp topologyC、Router# show ip eigrp interfacesD、Router# show ip eigrp neighbors
考题
网络管理员在路由器上进行故障排除的EIGRP问题，需要确认与路由器建立邻接设备的IP地址。重发间隔和相邻的路由器的队列计数也需要进行检查。什么命令会显示所需的信息？（）A、 Router# show ip eigrp adjacencyB、 Router# show ip eigrp topologyC、 Router# show ip eigrp interfacesD、 Router# show ip eigrp neighbors
考题
A router has EIGRP configured as the only routing protocol. How does EIGRP respond if there is no feasible successor route to a destination network and the successor route fails?（）A、It immediately sends its entire routing table to its neighbors.B、EIGRP sends a Hello packet to the DR to inform it of the route failure.C、It automatically forwards traffic to a fallback default route until a successor route is found.D、It sends queries out to neighbors until a new successor route is found.E、It places the route in holddown until LSA updates inform it of a new route to the network.
考题
Which of the following are methods EIGRP uses to initially populate (seed) its EIGRP topology table, before learning topology data from neighbors？（）A、By adding all subnets listed by the show ip route connected commandB、By adding the subnets of working interfaces over which static neighbors have been definedC、By adding subnets redistributed on the local router from another routing sourceD、By adding all subnets listed by the show ip route static command
考题
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）A、The show ip eigrp neighbors command on R1 lists the revised Hello timerB、The show ip eigrp interfaces command on R1 lists the revised Hello timerC、The R1 - R2 neighborship fails due to Hello timer mismatcHD、The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
考题
A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）A、show ip eigrp topologyB、show ip eigrp topology all - linksC、show ip route eigrpD、show ip route eigrp all - linksE、show ip eigrp topology all - learned
考题
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
考题
单选题网络管理员在路由器上进行故障排除的EIGRP问题，需要确认与路由器建立邻接设备的IP地址。重发间隔和相邻的路由器的队列计数也需要进行检查。什么命令会显示所需的信息？（）A
Router# show ip eigrp adjacencyB
Router# show ip eigrp topologyC
Router# show ip eigrp interfacesD
Router# show ip eigrp neighbors
考题
单选题A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）A
Router# show ip eigrp adjacencyB
Router# show ip eigrp topologyC
Router# show ip eigrp interfacesD
Router# show ip eigrp neighbors
考题
单选题TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?（）A
TestKing# show eigrp entriesB
TestKing# show protocolsC
TestKing# debug eigrp routesD
TestKing# show ip route eigrpE
TestKing# show route eigrp
考题
单选题Which command will display all the EIGRP feasible successor routes known to a router?（）A
Router# show ip eigrp routes *B
Router# show ip eigrp summaryC
Router# show ip eigrp topologyD
Router# show ip eigrp adjacenciesE
Router# show ip eigrp neighbors detail
考题
单选题An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（） Network Next Hop Metric LocPrf Weight Path * 3.3.3.3 0 0 1 1 1 1 2 18 iA
The Enterprise likely uses ASN 1.B
The neighboring ISP likely uses ASN 1.C
The route has been advertised through ASN 1 multiple times.D
Router Ent1 will add another ASN to the AS_Path before advertising this route to its iBGP peer (4.4.4.4).
考题
多选题Which of the following are methods EIGRP uses to initially populate (seed) its EIGRP topology table, before learning topology data from neighbors？（）ABy adding all subnets listed by the show ip route connected commandBBy adding the subnets of working interfaces over which static neighbors have been definedCBy adding subnets redistributed on the local router from another routing sourceDBy adding all subnets listed by the show ip route static command
考题
单选题Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）A
The show ip eigrp neighbors command on R1 lists the revised Hello timerB
The show ip eigrp interfaces command on R1 lists the revised Hello timerC
The R1 - R2 neighborship fails due to Hello timer mismatcHD
The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
考题
单选题Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A
R1 has been configured with an ip default- network 2.0.0.0 command.B
R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C
R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D
Another router has been configured with an ip default - network 2.0.0.0 command.E
Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
热门标签
最新试卷