网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?()
A. reset of the primary supervisor
B. manual switchover from standby to active supervisor
C. manual switchover from active to standby supervisor
D. automatic switchover from active to standby on primary supervisor failure
参考答案
更多 “ What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?() A. reset of the primary supervisorB. manual switchover from standby to active supervisorC. manual switchover from active to standby supervisorD. automatic switchover from active to standby on primary supervisor failure ” 相关考题
考题
Click the Exhibit button.In the exhibit, which statement is correct? ()
A. Three physical interfaces are redundant.B. You must define an additional Redundancy Group.C. node 0 will immediately become primary in the cluster.D. You must issue an operational command and reboot the system for the above configuration to take effect.
考题
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）A. using DHCP snoopingB. snooping the incoming 802.1Q VLAN tagC. using CDPD. snooping the CoS marking on the incoming frames
考题
As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）A. Automatic switchover from active to standby on primary supervisor failureB. Reset of the primary supervisor.C. Manual switchover from active to standby supervisorD. Manual switchover from standby to active supervisor
考题
What will happen if you issue the redundancy force－switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? ()
A. reset of the primary supervisorB. manual switchover from standby to active supervisorC. manual switchover from active to standby supervisorD. automatic switchover from active to standby on primary supervisor failure
考题
Which statement best describes Cisco supervisor engine redundancy using Stateful Switchover？（）A、Switchover ensures that Layer 2 through Layer 4 traffic is not interruptedB、Redundancy requires BGP， OSPF， EIGRP， or IS-ISC、Redundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switchesD、Switchover can be caused by clock synchronization failure between supervisors
考题
You need to troubleshoot an issue on the switched LAN. When you issue a command "show port3/1" on a switch， you observe the Giants column has a non-zero entry. What could cause this？（）A、IEEE 802.10B、Misconfigured NICC、User configurationD、IEEE 802.1QE、None of the other alternatives apply
考题
Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy using NSF？（）A、 independent of SSOB、 NSF combined with SSO enables supervisor engine load balancingC、 supported by RIPv2， OSPF， IS-IS， and EIGRPD、 supports IPv4 and IPv6 multicastE、 prevents route flappingF、 dependent on FIB tables
考题
You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A、 Catalyst 2960 SeriesB、 Catalyst 3750 SeriesC、 Catalyst 4900 SeriesD、 Catalyst 6500 Series
考题
When applying the configuration in the exhibit and initializing a chassis cluster， which statement is correct？（） [edit chassis] user@host# show cluster { reth-count 3； redundancy-group 1 { node 0 priority 1； node 1 priority 100； } }A、Three physical interfaces are redundant.B、You must define an additional redundancy group.C、node 0 will immediately become primary for redundancy group 1.D、You must issue an operational command and reboot the system for the above configuration to take effect.
考题
What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）A、The switch will ignore VTP summary advertisements.B、The switch will forward VTP summary advertisements.C、The switch will process VTP summary advertisements.D、The switch will originate VTP summary advertisements.E、The switch will create, modify and delete VLANs for the entire VTP domain.
考题
What will happen if you issue the redundancy force-switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?（）A、reset of the primary supervisorB、manual switchover from standby to active supervisorC、manual switchover from active to standby supervisorD、automatic switchover from active to standby on primary supervisor failure
考题
Company has a Catalyst 6500 and you need to configure redundancy between the supervisormodules. With route processor redundancy （RPR+）， the redundant supervisor engine is fullyinitialized and configured， which shortens the switchover time if the active supervisor engine fails.Which three statements are true about the RPR + operations when the redundant supervisorengine switched over the failed primary supervisor engine？（）A、Static IP routes are maintained across a switchover because they are configured from entries inthe configuration fileB、Information about dynamic routing states， maintained on the active supervisor engine， issynchronized to the redundant supervisor engine and is transferred during the switchoverC、Information about dynamic routing states， maintained on the active supervisor engine， is notsynchronized to the redundant supervisor engine and is lost on switchoverD、The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routedtraffic is interrupted until route tables reconvergeE、Static IP routes are cleared across a switchover and recreated from entries in the configurationfile on the redundant supervisor engineF、The Forwarding Information Base （FIB） tables are maintained during the switchover. As aresult， routed traffic continues without any interruption when the failover occurs
考题
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）A、using DHCP snoopingB、snooping the incoming 802.1Q VLAN tagC、using CDPD、snooping the CoS marking on the incoming frames
考题
How many access points will a Cisco 7600 Series Router with six installed Cisco Catalyst 6500Series Wireless Services Modules support？（）A、300B、448C、664D、1800E、2400
考题
What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）A、The switch will ignore VTP summary advertisementsB、The switch will forward VTP summary advertisementsC、The switch will process VTP summary advertisementsD、The switch will originate VTP summary advertisementsE、The switch will create, modify and delete VLANs for the entire VTP domain
考题
单选题You have enabled backup optimization in RMAN. You issue the following RMAN command to configure a redundancy-based retention policy: CONFIGURE RETENTION POLICY TO REDUNDANCY 3; Which statement is true?（）A
The command fails because you cannot configure a redundancy-based retention policy when backup optimization is enabledB
Backup optimization is performed, but RMAN considers the redundancy-based retention policy when it determines which datafiles should be backed upC
Backup optimization is permanently disabledD
Backup optimization is temporarily disabled because a redundancy-based retention policy is specified
考题
单选题You have enabled backup optimization in RMAN. You issue the following RMAN command to configure a redundancy-based retention policy： CONFIGURE RETENTION POLICY TO REDUNDANCY 3； Which statement is true？（）A
The command fails because you cannot configure a redundancy-based retention policy when backup optimization is enabledB
Backup optimization is performed， but RMAN considers the redundancy-based retention policy when it determines which datafiles should be backed upC
Backup optimization is permanently disabledD
Backup optimization is temporarily disabled because a redundancy-based retention policy is specified
考题
单选题A manufacturing customer has an IBM BladeCenter H chassis with four， HX5 with MAX5 4-socket blades installed. Each blade has the optional Fibre Channel Expansion card. The customer wants redundancy and is going to install the following configuration： （1）two Brocade 20-Port SAN Switch Modules （2）two Nortel Networks 1/10 GB Uplink ESM （3）a redundant AMM What is the minimum number of power supplies needed for this configuration to have full redundancy？（）A
4B
3C
2D
8
考题
多选题Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy using NSF？（）Aindependent of SSOBNSF combined with SSO enables supervisor engine load balancingCsupported by RIPv2， OSPF， IS-IS， and EIGRPDsupports IPv4 and IPv6 multicastEprevents route flappingFdependent on FIB tables
考题
多选题What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）AThe switch will ignore VTP summary advertisementsBThe switch will forward VTP summary advertisementsCThe switch will process VTP summary advertisementsDThe switch will originate VTP summary advertisementsEThe switch will create, modify and delete VLANs for the entire VTP domain
考题
单选题You need to troubleshoot an issue on the switched LAN. When you issue a command "show port3/1" on a switch， you observe the Giants column has a non-zero entry. What could cause this？（）A
IEEE 802.10B
Misconfigured NICC
User configurationD
IEEE 802.1QE
None of the other alternatives apply
考题
多选题pany has a Catalyst 6500 and you need to configure redundancy between the supervisor modules. With route processor redundancy （RPR+）， the redundant supervisor engine is fully initialized and configured， which shortens the switchover time if the active supervisor engine fails. Which three statements are true about the RPR + operations when the redundant supervisor engine switched over the failed primary supervisor engine？ （）AStatic IP routes are maintained across a switchover because they are configured from entries in the configuration file.BInformation about dynamic routing states， maintained on the active supervisor engine， is synchronized to the redundant supervisor engine and is transferred during the switchover.CInformation about dynamic routing states， maintained on the active supervisor engine， is not synchronized to the redundant supervisor engine and is lost on switchover.DThe Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routed traffic is interrupted until route tables reconverge.EStatic IP routes are cleared across a switchover and recreated from entries in the configuration file on the redundant supervisor engine.FThe Forwarding Information Base （FIB） tables are maintained during the switchover. As a result， routed traffic continues without any interruption when the failover occurs.
考题
单选题As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）A
Automatic switchover from active to standby on primary supervisor failureB
Reset of the primary supervisor.C
Manual switchover from active to standby supervisorD
Manual switchover from standby to active supervisor
考题
单选题You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A
Catalyst 2960 SeriesB
Catalyst 3750 SeriesC
Catalyst 4900 SeriesD
Catalyst 6500 Series
考题
单选题What will happen if you issue the redundancy force-switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? （）A
reset of the primary supervisorB
manual switchover from standby to active supervisorC
manual switchover from active to standby supervisorD
automatic switchover from active to standby on primary supervisor failure
考题
单选题If you issue the command shutdown abort prior to trying to put the database in ARCHIVELOG mode， what will be the result when you issue the command alter database archivelog？（）A
The alter database archivelog command will failB
The alter database archivelog inconsistent command must be used to put the database in ARCHIVELOG modeC
The alter database archivelog command will succeedD
The alter database archivelog command will ask if you want to make the database consistent firstE
There is no alter database archivelog command. The correct command is alter database alterlogging
考题
单选题Click the Exhibit button. In the exhibit, which statement is correct? （）A
Three physical interfaces are redundant.B
You must define an additional Redundancy Group.C
node 0 will immediately become primary in the cluster.D
You must issue an operational command and reboot the system for the above configuration to take effect.
热门标签
最新试卷