多选题Assume two routers on the same subnet， R1 and R2， both configured for HSRP. R1 has a priority of 120.Which of the following HSRP interface configurations will always result in the R2 becoming the primary？（）Astandby 1 priority 110Bstandby 1 priority 120Cstandby 1 priority 130Dstandby 1 priority 110 preemptEstandby 1 priority 120 preemptFstandby 1 priority 130 preempt

考题 Routers A and B are connected with a point-to-point OC-3 interface. Each router‘s OC-3 interface is configured for both Level 1 and Level 2. The routers are configured in the same area.How many IS-IS adjacencies exist between the two routers?（）A.0B.1C.2D.3

查看答案

考题 Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.

查看答案

考题 Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP

查看答案

考题 The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?（）A. The authentication needs to be changed to PAP for both routers.B. The serial IP addresses of routers are not on the same subnet.C. The username/password combination is incorrectly configured.D. The router names are incorrectly configured.

查看答案

考题 Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true? () A. Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.B. All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.C. Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.D. All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.

查看答案

考题 S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?（）A.Configure the no ip subnet-zero command on R1, R2, and R3.B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.

查看答案

考题 The administrator is unable to establish connectivity between two Cisco routers. Upon reviewing the command output of both routers, what is the most likely caust of the problem?() A.Authentication needs to be changed to PAP for both routers.B.Serial IP addresses of routers are not on the same subnet.C.Username/password is incorrectly configured.D.Router names are incorrectly configured.

查看答案

考题 Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）A、R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1B、R1 can send IP packets to R2, but R2 cannot send IP packets to R1C、R2 no longer learns EIGRP routes from R1 for routes not connected to R1D、R1 no longer replies to R2's Query messagesE、R2n o longer sends to R1 Query messages

查看答案

考题 Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers. B、 Routers configured for HSRP can belong to multiple groups and multiple VLANs.C、 Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.D、 All routers configured for HSRP load balancing must be configured with the same priority. E、 Routers configured for HSRP must belong to only one group per HSRP interface.

查看答案

考题 Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）A、Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.B、R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.C、R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.D、All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.

查看答案

考题 Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）A、HostA is not on the same subnet as its default gatewayB、The address of SwitchA is a subnet addressC、The Fa0/0 interface on RouterA is on a subnet that cannot be usedD、The serial interfaces of the routers are not on the same subnetE、The Fa0/0 interface on RouterB is using a broadcast address

查看答案

考题 In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）A、Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.B、A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.C、A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.D、A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.

查看答案

考题 Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.B、 The default priority of a router is zero （0）.C、 The no standby priority command assigns a priority of 100 to the router.D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.

查看答案

考题 Routers A and B are connected with a point-to-point OC-3 interface. Each router's OC-3 interface is configured for both Level 1 and Level 2. The routers are configured in the same area. How many IS-IS adjacencies exist between the two routers?（）A、0B、1C、2D、3

查看答案

考题 Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）A、frame - relay map commands on R3 - R10 referencing the other routers in this groupB、Nine OSPF neighbor commands on each routerC、Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10D、R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRE、R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR

查看答案

考题 Routers R1, R2, R3, and R4 connect to the same 10.10.10.0/24 LAN- based subnet. OSPF is fully working in the subnet. Later, R5, whose OSPF priority is higher than the other four routers, joins the subnet. Which of the following are true about the OSPF database exchange process over this subnet at this point?（）A、R5 will send its DD, LSR, and LSU packets to the 224.0.0.5 all - DR - routers multicast address.B、R5 will send its DD, LSR, and LSU pack ets to the 224.0.0.6 all - DR - routers multicast address.C、The DR will inform R5 about LSAs by sending its DD, LSR, and LSU packets to the 224.0.0.6 all- SPF - routers multicast address.D、The DR will inform R5 about LSAs by sending its DD, LSR, and LSU pa ckets to the 224.0.0.5 all- SPF - routers multicast address.

查看答案

考题 If two routers， both reachable from one another， originate functionally equivalent type 2 external- LSAs （i.e，same destination， cost and non-zero forwarding address ）， Which of the following statements wouldapply ？（）A、Two LSAs will exist in the network for this destination， and both will be usedB、Two LSAs will exist in the network for this destination， but only the one generated by the highest RID ASBR will be usedC、Only the LSA generated by the highest RID ASBR will exist in the networkD、Only the LSA generated by the lowest RID ASBR will exist in the network

查看答案

考题 Assume two routers on the same subnet， R1 and R2， both configured for HSRP. R1 has a priority of 120.Which of the following HSRP interface configurations will always result in the R2 becoming the primary？（）A、standby 1 priority 110B、standby 1 priority 120C、standby 1 priority 130D、standby 1 priority 110 preemptE、standby 1 priority 120 preemptF、standby 1 priority 130 preempt

查看答案

考题 Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）A、The show ip ospf neighbors command lists two neighbors off Fa0/0.B、The show ip ospf neighbors command lists four neighbors off Fa0/0.C、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.D、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.

查看答案

考题单选题In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）A Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.B A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.C A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.D A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.

查看答案

考题多选题Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）ALoad sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.BRouters configured for HSRP can belong to multiple groups and multiple VLANs.CLoad sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.DAll routers configured for HSRP load balancing must be configured with the same priority.ERouters configured for HSRP must belong to only one group per HSRP interface.

查看答案

考题单选题Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）A Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.B R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.C R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.D All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.

查看答案

考题多选题Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）Aframe - relay map commands on R3 - R10 referencing the other routers in this groupBNine OSPF neighbor commands on each routerCNine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10DR1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRER3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR

查看答案

考题单选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）A The next hop is I2's BGP RIDB The next hop is I2's IP address used on the R2 - I2 neigh bor relationshipC The next hop is R2's BGP RIDD The next hop is R2's IP address used on the R1 - R2 neighbor relationship

查看答案

考题多选题Refer to the exhibit. There are two sites connected across WAN links. All intersite and intrasite links always have the same routing metric. The network administrator sees only the top routers and links being used by hosts at both LAN A and LAN B. What would be two suggestions to load-balance the traffic across both WAN links？（）AMake HSRP track interfaces between the edge and core routers.BReplace HSRP with GLBP. 用GLBP替换HSRPCAdd crossed intrasite links： R1-R4， R2-R3， R5-R8， and R6-R7.DMake R3 and R8 have lower HSRP priority than R1 and R7.EReplace HSRP with VRRP

查看答案

考题多选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers. Which of the following could be used to prevent potential routing loops in this design?（）AUsing an iBGP mesh inside the Enterprise coreBConfiguring default routes in the Enterprise pointing to both R1 and R2CRedistributing BGP routes into the Enterprise IGPDTunneling the packets for the i BGP connection between R1 and R2

查看答案

考题多选题Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）AThe show ip ospf neighbors command lists two neighbors off Fa0/0.BThe show ip ospf neighbors command lists four neighbors off Fa0/0.CThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.DThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.

查看答案

考题单选题The administrator is unable to establish connectivity between two Cisco routers. Upon reviewing the command output of both routers, what is the most likely caust of the problem?（）A Authentication needs to be changed to PAP for both routers.B Serial IP addresses of routers are not on the same subnet.C Username/password is incorrectly configured.D Router names are incorrectly configured.

查看答案

网友您好， 请在下方输入框内输入要搜索的题目：

网友您好，请在下方输入框内输入要搜索的题目：