多选题A single 802.11g access point has been configured and installed in the center of a square officE.A few wireless users are experiencing slow performance and drops while most users are operating at peak efficiency. What are three likely causes of this problem? （）Amismatched TKIP encryptionBnull SSIDCcordless phonesDmismatched SSIDEmetal file cabinetsFantenna type or direction

考题 A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero

查看答案

考题 Refer to the exhibit. Switch port FastEthernet 0/24 on AlSwitch1 will be used to create an IEEE 802.1Q- complaint trunk to another switch. Based on the output shown, What is the reason the trunk does not form, even thought the proper cabling has been attached?（）A.VLANs have not been created yetB.An IP address must be configured for the portC.The port is currently configured for access modeD.The correct encapsulation type has not been configuredE.The no shutdown command has not been entered for the port

查看答案

考题 Vlans have been enabled on an autonomous access point. in order for clients associating to vlans other than the native vlan to receive an ip address. Which of the following must be configured？（）A、access point ethernet port set to ssl trunkingB、switchport set to 802.1q trunkingC、switchport set to ssl trunkingD、access point ethernet port not set to 802.1q trunking

查看答案

考题 A single 802.11g access point has been configured and installed in the center of a square office. A few wireless users are experiencing slow performance and drops while most users are operating at peak efficiency. What are three likely causes of this problem (Choose three.)（）。A、mismatched TKIP encryptionB、null SSIDC、cordless phonesD、mismatched SSIDE、metal file cabinetsF、antenna type or direction

查看答案

考题 A lightweight access point has been connected to a Catalyst 3550 24-PWR switch， and on power-up the access point fails. What is the problem with the switch？（）A、The power supply has inadequate wattage.B、Power is incorrectly configured on the port.C、It does not support 802.3af Poe.D、Power is not enabled on the port.

查看答案

考题 A new Aironet 1200 series AP has been installed in the Company WLAN. What happens when this device is connected to the LAN， with a default configuration？（）A、 The access point will attempt to download an encryption key from the nearest wireless server.B、 The access point makes several attempts to get an IP address from the DHCP server. If the access point does not receive an address， it assigns itself the IP address 10.0.0.1 for 5 minutes.C、 The access point will attempt to connect to the nearest wireless server using LEAP authentication.D、 The access point requests an IP address from the DHCP server. If the access point does not receive an address， it continues to send requests indefinitely.E、 None of the other alternatives apply

查看答案

考题 An reap was supporting 16 wlans， but now it only supports one. What happened to cause the change？（）A、controller connectivity has been lost.B、the access point lost its configuration.C、the access point was rebooted.D、an access point firmware upgrade is in progress.

查看答案

考题 All users within an office are wirelessly connected to a network, except one user that has a valid connection on a leased IP address in a different range. Which of the following is a possible cause of the user having a different IP address range?（）A、The wireless access point is using MAC address filteringB、The user has connected to a nearby wireless access point from another officeC、The user has configured the wireless settings with the wrong encryption typeD、The wireless access point has SSID broadcast disabled

查看答案

考题 A single 802.11g access point has been configured and installed in the center of a square office. A few wireless users are experiencing slow performance and drops while most users are operating at peak efficiency. What are three likely causes of this problem? (Choose three.) （）A、mismatched TKIP encryption B、null SSID C、cordless phones D、mismatched SSID E、metal file cabinetsF、antenna type or direction

查看答案

考题 A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24PWR Switch. However， when it is powered up， the access point fails. What has caused this problem？（）A、access point does not support 802.11hB、incorrect switch power supplyC、switch port is not enabledD、switch does not support 802.3afE、access point has not been initialized with the primary controller

查看答案

考题 How does a controller-based access point configured to operate in sniffer mode behave？（）A、allows client traffic， captures data on all channelsB、allows client traffic， captures data on a single channelC、allows no client traffic， captures data on all channelsD、allows no client traffic， captures data on a single channel

查看答案

考题 A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However， when it is powered up， the access point fails. What has caused this problem？（）A、access point does not support 802.11hB、incorrect switch power supplyC、switch port is not enabledD、switch does not support 802.3afE、access point has not been initialized with the primary controller

查看答案

考题 Your client has deployed a cisco wireless location appliance within their warehouse environment. they have been experiencing problems with tracking objects using active rfid tags. to verify proper access point deployment for location server. The results from an access point scan should show what information？（）A、a minimum rssi value of -50B、rogue access pointsC、a minimum of three access pointsD、non-overlapping channels

查看答案

考题 A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero

查看答案

考题单选题Refer to the exhibit. A Cisco Aironet Wireless LAN Client Adapter has been installed and configured through the ADU on the PC. The Aironet System Tray Utility （ASTU） has been enabled during the installation and the icon appears in the system tray area in the lower right of the desktop. What is thesignificance of the icon？（）A It indicates that the radio of the client adapter is disabledB It indicates that the client adapter is not associated to an access point or another clientC It indicates that the client adapter is associated to an access point or another client， but the user is not EAP authenticatedD It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is excellent or goodE It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is fairF It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is poor

查看答案

考题单选题A cisco aironet 1020 controller-based access point has been connected to a catalyst 3550-24 pwr switch. however， when it is powered up， the access point fails. What has caused this problem？（）A access point does not support 802.11hB incorrect switch power supplyC switch port is not enabledD switch does not support 802.3afE access point has not been initialized with the primary controller

查看答案

考题单选题Refer to the exhibit. A Cisco Aironet Wireless LAN Client Adapter has been installed and configured through the ADU on the PC. The Aironet System Tray Utility （ASTU） has been enabled during the installation and the icon appears in the system tray area in the lower right of the desktop. What is the significance of the icon？（）A It indicates that the radio of the client adapter is disabled.B It indicates that the client adapter is not associated to an access point or another client. C It indicates that the client adapter is associated to an access point or another client， but the user is not EAP authenticated.D It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is excellent or good.E It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is fair.F It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is poor.

查看答案

考题单选题An reap was supporting 16 wlans， but now it only supports one. What happened to cause the change？（）A controller connectivity has been lost.B the access point lost its configuration.C the access point was rebooted.D an access point firmware upgrade is in progress.

查看答案

考题单选题Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）A client traffic allowed， data captured on all channelsB client traffic allowed， data captured on a single channelC no client traffic allowed， data captured on a single channelD no client traffic allowed， data captured on all channels

查看答案

考题多选题A new lightweight access point （LAP） has been installed in the Company WLAN. Which two statements correctly describe the association process between this LAP and a WLAN controller？（）AAn access point will search for a controller using a broadcast address if using LWAPP Layer 2 and a unicast address if using LWAPP Layer 3 mode.BIf multiple wireless controllers are detected by an access point， the controller with the fewest associated access points is chosen to associate with.CIn order to associate in Layer 3 mode， the access point must have been preconfigured with an IP address.DOnce an access point associates with a controller in LWAPP Layer 3 mode， it receives an IP address from the controller.EAn access point first searches for a controller in LWAPP Layer 2 mode. If the search is not successful， the access point then attempts to locate a controller in LWAPP Layer 3 mode.FIf multiple wireless controllers are detected by an access point， all of them will be used and traffic will be load balanced.

查看答案

考题单选题A lightweight access point has been connected to a Catalyst 3550 24-PWR switch， and on power-up the access point fails. What is the problem with the switch？（）A The power supply has inadequate wattage.B Power is incorrectly configured on the port.C It does not support 802.3af Poe.D Power is not enabled on the port.

查看答案

考题单选题All users within an office are wirelessly connected to a network, except one user that has a valid connection on a leased IP address in a different range. Which of the following is a possible cause of the user having a different IP address range?（）A The wireless access point is using MAC address filteringB The user has connected to a nearby wireless access point from another officeC The user has configured the wireless settings with the wrong encryption typeD The wireless access point has SSID broadcast disabled

查看答案

考题多选题A single 802.11g access point has been configured and installed in the center of a square office. A few wireless users are experiencing slow performance and drops while most users are operating at peak efficiency. What are three likely causes of this problem? (Choose three.) （）Amismatched TKIP encryptionBnull SSIDCcordless phonesDmismatched SSIDEmetal file cabinetsFantenna type or direction

查看答案

考题单选题A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24PWR Switch. However， when it is powered up， the access point fails. What has caused this problem？（）A access point does not support 802.11hB incorrect switch power supplyC switch port is not enabledD switch does not support 802.3afE access point has not been initialized with the primary controller

查看答案

网友您好， 请在下方输入框内输入要搜索的题目：

网友您好，请在下方输入框内输入要搜索的题目：