网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
When enabling a tty port to be used for a cu session， what must be done on the system？（）
A
smit tty； take the defaults and create the desired tty
B
lsdev -Cc tty； check to see if the desired tty exists， if not create using smit tty Add a line similar to； Direct tty0 - 9600 direct to /etc/uucp/Devices Verify /etc/uucp/Dialers has the following line； direct
C
Install bos.net.uucp and the first available tty will be configured for use by a cu session
D
Run the Asynchronous Terminal Emulation （ate） program and it will configure a tty port for a cu session
参考答案
参考解析
解析：
暂无解析
更多 “单选题When enabling a tty port to be used for a cu session， what must be done on the system？（）A smit tty； take the defaults and create the desired ttyB lsdev -Cc tty； check to see if the desired tty exists， if not create using smit tty Add a line similar to； Direct tty0 - 9600 direct to /etc/uucp/Devices Verify /etc/uucp/Dialers has the following line； directC Install bos.net.uucp and the first available tty will be configured for use by a cu sessionD Run the Asynchronous Terminal Emulation （ate） program and it will configure a tty port for a cu session” 相关考题
考题
Which statement is true when you enable SSL for the WebUI?()
A. SSL is enabled for the WebUI by default.B. You must address the WebUI using HTTPS://.C. You must change the WebUI port when enabling SSL.D. The demokey and democert are applied to the WebUI by default.
考题
What are two functions that the parameter max－session performs? ()(Choose two.)
A. Defines the session limit for the domain.B. Defines the session limit for the tunnel instance.C. Used to control load balancing between multiple domains.D. Used to control load balancing between multiple tunnels for a domain.
考题
After enabling port security on a Cisco Catalyst switch， what is the default action when the configuredmaximum of allowed MAC addresses value is exceeded？（）A、The port’s violation mode is set to restrictB、The port is shut downC、The MAC address table is cleared and the new MAC address is entered into the tableD、The port remains enabled， but bandwidth is throttled until old MAC addresses are aged out
考题
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology？（）A、lowest port MAC addressB、port priority number and MAC addressC、VTP revision numberD、highest port priority numberE、path cost
考题
What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-treetopology?（）A、lowest port MAC addressB、port priority number and MAC address.C、VTP revision numberD、highest port priority number.E、pathcost
考题
What are the "bound IP addresses" used for in LDP？（）A、For each such address and mask /32, one label binding is created.B、As the TCP endpoint, IP addresses are used by the LDP session.C、These addresses are used to find the label binding to put in the LFIB, by looking up these IP addresses in the routing table.D、These addresses are used for penultimate hop popping (PHP) when forwarding packets to the next router directly.
考题
What value is primarily used to determine which port becomes the root port on each non root switch in a spanning-tree topology?（）A、path costB、lowest port MAC addressC、VTP revision numberD、highest port priority numberE、port priority number and MAC address
考题
Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning session， it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network. What should be done to ensure the serial network will function with HACMP heartbeats？（） A、 Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.B、 Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.C、 Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.D、 Verify with IBM support which native serial ports for the server model can be used for HACM pheartbeats.
考题
Which of the following is TRUE about the ate program？（）A、When running ate for the first time it will prompt for all the required information and configure all the required devicesB、The program is used by cu to communicate to a remote systemC、The program is used for remote communications between the host and a remote system using a modem or null modem via a tty portD、The program ate calls cu to communicate with the remote system
考题
What features set is most frequently used to prevent hackers from flooding a port with MAC- addresses？（）A、BPDU GuardB、802.xC、Port SecurityD、Storm Control
考题
When a switch port is used as a VLAN trunk, which of the following trunk modes are valid?（）A、BlockingB、AutoC、DesirableD、OnE、TransparentF、Learning
考题
What is the correct fastpath to configure or add a TTY Terminal （directly from the screen）， which connects to a serial port？（）A、smitty ttyB、smitty devicesC、smitty ptyD、smitty dev
考题
Which of the following commands should be used to open a tty port configured in the /etc/uucp/Devices file as： Direct tty2 - 9600 direct in debug mode， ignoring modem control signal data carrier detect （DCD）？（）A、cu -l tty2B、cu -dml tty2C、cu -dht DirectD、cu -s9600 -l tty2
考题
Which of the following commands should be used to check the settings for a new tty that was just set up as tty2？（）A、lsattr -El tty2B、lscons -d /dev/tty2C、lscfg -vl tty2D、what /dev/tty2
考题
Which statement is true when you enable SSL for the WebUI?（）A、SSL is enabled for the WebUI by default.B、You must address the WebUI using HTTPS://.C、You must change the WebUI port when enabling SSL.D、The demokey and democert are applied to the WebUI by default.
考题
A system administrator has created tty2 on a serial port connection to a system. When attempting to verify the connection the following error is observed： # cu -ml tty2 cu： 0835-028 The connection failed. NO DEVICES AVAILABLE. Which of the following should be performed to correct this error？（）A、Create an entry for tty2 in the /etc/uucp/Devices fileB、Re-enter the command as "cu -dml tty2"C、Create an entry for tty2 in the /etc/uucp/Systems fileD、Re-enter the command as "cu -s 9600 -dh -t -l tty2"
考题
单选题Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning session， it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network. What should be done to ensure the serial network will function with HACMP heartbeats？（）A
Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.B
Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.C
Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.D
Verify with IBM support which native serial ports for the server model can be used for HACM pheartbeats.
考题
单选题Which statement is true when you enable SSL for the WebUI?（）A
SSL is enabled for the WebUI by default.B
You must address the WebUI using HTTPS://.C
You must change the WebUI port when enabling SSL.D
The demokey and democert are applied to the WebUI by default.
考题
多选题When a switch port is used as a VLAN trunk, which of the following trunk modes are valid?（）ABlockingBAutoCDesirableDOnETransparentFLearning
考题
单选题After enabling port security on a Cisco Catalyst switch， what is the default action when the configuredmaximum of allowed MAC addresses value is exceeded？（）A
The port’s violation mode is set to restrictB
The port is shut downC
The MAC address table is cleared and the new MAC address is entered into the tableD
The port remains enabled， but bandwidth is throttled until old MAC addresses are aged out
考题
单选题Which of the following is TRUE about the ate program？（）A
When running ate for the first time it will prompt for all the required information and configure all the required devicesB
The program is used by cu to communicate to a remote systemC
The program is used for remote communications between the host and a remote system using a modem or null modem via a tty portD
The program ate calls cu to communicate with the remote system
考题
单选题What are the "bound IP addresses" used for in LDP？（）A
For each such address and mask /32, one label binding is created.B
As the TCP endpoint, IP addresses are used by the LDP session.C
These addresses are used to find the label binding to put in the LFIB, by looking up these IP addresses in the routing table.D
These addresses are used for penultimate hop popping (PHP) when forwarding packets to the next router directly.
考题
单选题To enable a tty port to be used for a cu session what must be done to the system？（）A
smit tty； take the defaults and create the desired ttyB
In the /etc/uucp Devices add a line similar to： Direct ttyX - 9600 directC
Install bos.net.uucp and the first available tty will be configured for use by a cu sessionD
Run the Asynchronous Terminal Emulation （ATE） program and it will configure a tty port for a cu session
考题
单选题Which of the following commands should be used to open a tty port configured in the /etc/uucp/Devices file as： Direct tty2 - 9600 direct in debug mode， ignoring modem control signal data carrier detect （DCD）？（）A
cu -l tty2B
cu -dml tty2C
cu -dht DirectD
cu -s9600 -l tty2
热门标签
最新试卷