网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
Refer to the exhibit. With an IPSec tunnel established between remote Router A and head-end router B, with Compressed Real-Time Protocol (cRTP) configured on the serial interface of Router A, what impact will the cRTP configuration have on the Voice over IP packets flowing through the IPSec tunnel from a Cisco 7960 IP phone?（）
A
Twenty bytes of header will be replaced with five bytes.
B
If the IPSec transform set includes Authentication Header, the receiving IPSec peer will discard the packets.
C
The IPSec packets will be dropped by Router A's compression logic.
D
The voice packets will not be compressed.
参考答案
参考解析
解析：
暂无解析
更多 “单选题Refer to the exhibit. With an IPSec tunnel established between remote Router A and head-end router B, with Compressed Real-Time Protocol (cRTP) configured on the serial interface of Router A, what impact will the cRTP configuration have on the Voice over IP packets flowing through the IPSec tunnel from a Cisco 7960 IP phone?（）A Twenty bytes of header will be replaced with five bytes. B If the IPSec transform set includes Authentication Header, the receiving IPSec peer will discard the packets. C The IPSec packets will be dropped by Router A's compression logic.D The voice packets will not be compressed.” 相关考题
考题
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?()
A. The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB. The router must hav e at least one working link connected to each routing domainC. The redistribute command must be configured under EIGRP to send the routes to OSPFD. The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
考题
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
考题
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.
考题
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
考题
Refer to the parti al configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?()
A. the serial 1/1 addressB. the serial 2/0 addressC. a randomly generated internal addressD. the configured router - id address
考题
Refer to the exhibit. What three statements are true about the IS － IS configuration?()
A.The router is in area 49.0001.0002B.The router acts as a Level 1 - 2 routerC.CLNS routing is enable d for the routerD.The router has a system ID of 0003.0004E.The interfaces have a functional IS - IS configurationF.The network service access point selector (NSEL) byte has a value of 0
考题
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
考题
Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? ()
A. Router A will prefer the path through router B for network 172.20.0.0B. Router A will prefer the path through router C for network 172.20.0.0C. Packets from router D will prefer the path through router B for networks advertised by router AD. Packets from r outer D will prefer the path through router C for networks advertised by router A
考题
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）A. The Popcorn router is not forwarding RIP updates.B. The Popcorn router did not include network 192.168.12.0 in its routing configuration.C. The Ethernet1 interface of the Popcorn router is shutdown.D. The clockrate is not present in the configuration of one of the routers.E. The Serial interface of the Popcorn router is not operating.
考题
Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?（）A.The design will function as intendedB.Spanning-tree will need to be used.C.The router will not accept the addressing scheme.D.The connection between switches should be a trunk.E.The router interfaces must be encapsulated with the 802.1Q protocol.
考题
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?()
A.As numbers must be changed to match on all the routers.B.Loopback interface must be configured so a DR is elected.C.The no auto-summary command is needed on Router A and Router C.D.Router B needs to have two network statements, one for each connected network.
考题
Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? （）A.The Manchester serial address is 10.1.1.1B.The Manchester serial address is 10.1.1.2C.这个Manchester路由器串口地址为：10.1.12D.The London router is a Cisco 2610.E.The Manchester router is a Cisco 2610.F.The CDP information was received on port Serial0/0 of the Manchester router.G.The CDP information was sent by port Serial0/0 of the London Router.
考题
Usetheoutputfromtheroutershowninthegraphicabovetodeterminewhichofthefollowingarecorrect.()
A.Router John uses alink-state routing protocol.B.Router John will receive routing updates on the Serial0/0 interface.C.Router John will receive routing updates on the Serial0/1 interface.D.Router John will send routing updates out the Serial0/0 interface.E.Router John will send routing updates out the FastEthernet0/0 interface.F.Router John will send routing updates out the Serial0/1 interface.
考题
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router.How should the network administrator configure the serial interface of the main office router to make the connection?（）A.B.C.D.
考题
Refer to the exhibit. A router has a 256 kbps Frame Relay circuit connected to interface serial 0/0. As a large FTP packet is being placed into the hardware transmit queue of interface serial 0/0， a voice packet is placed into the priority queue of that interface. How， and in what order， wi the packets be transmitted？（）A、the voice packet will be transmitted first， followed by the FTP packet in its entiretyB、the voice packet will be transmitted first， followed by the fragmented FTP packetC、the FTP packet will be fragmented and the voice packet will be interleavedD、the FTP packet will be transmitted first in its entirety， follow by the voice packet
考题
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。A、a switch with a trunk link that is configured between the switchesB、a router with an IP address on the physical interface that is connected to the switchC、a switch with an access link that is configured between the switchesD、a router with subinterfaces configured on the physical interface that is connected to the switch
考题
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）A、Serial 0 is up, line protocol is upB、Serial 0 is up, line protocol is downC、Serial 0 is down, line protocol is downD、Serial 0 is down, line protocol is upE、Serial 0 is administratively down, line protocol is downF、Serial 0 is administratively down, line protocol is up
考题
Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）A、The router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2B、The configuration is invalid because the DHCP options are global configuration commandsC、The configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesD、The router will choose which pool to use based upon the interface the DHCP request wasreceived on
考题
A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A、The process id is configured improperlyB、The OSPF area is configured improperlyC、The network wildcard mask is configured improperlyD、The network number is configured improperlyE、The AS is configured improperlyF、The network subnet mask is configuerd improperly
考题
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB、The router must hav e at least one working link connected to each routing domainC、The redistribute command must be configured under EIGRP to send the routes to OSPFD、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
考题
单选题Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A
As numbers must be changed to match on all the routers.B
Loopback interface must be configured so a DR is elected.C
The no auto-summary command is needed on Router A and Router C.D
Router B needs to have two network statements, one for each connected network.
考题
单选题Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）A
The router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2B
The configuration is invalid because the DHCP options are global configuration commandsC
The configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesD
The router will choose which pool to use based upon the interface the DHCP request wasreceived on
考题
单选题Refer to the exhibit. A router has a 256 kbps Frame Relay circuit connected to interface serial 0/0. As a large FTP packet is being placed into the hardware transmit queue of interface serial 0/0， a voice packet is placed into the priority queue of that interface. How， and in what order， wi the packets be transmitted？（）A
the voice packet will be transmitted first， followed by the FTP packet in its entiretyB
the voice packet will be transmitted first， followed by the fragmented FTP packetC
the FTP packet will be fragmented and the voice packet will be interleavedD
the FTP packet will be transmitted first in its entirety， follow by the voice packet
考题
单选题Refer to the exhibit. A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?（）A
The design will function as intendedB
Spanning-tree will need to be used.C
The router will not accept the addressing scheme.D
The connection between switches should be a trunk.E
The router interfaces must be encapsulated with the 802.1Q protocol.
考题
多选题The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）AThe Popcorn router is not forwarding RIP updates.BThe Popcorn router did not include network 192.168.12.0 in its routing configuration.CThe Ethernet1 interface of the Popcorn router is shutdown.DThe clockrate is not present in the configuration of one of the routers.EThe Serial interface of the Popcorn router is not operating.
考题
单选题A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0A
The process id is configured improperlyB
The OSPF area is configured improperlyC
The network wildcard mask is configured improperlyD
The network number is configured improperlyE
The AS is configured improperlyF
The network subnet mask is configuerd improperly
考题
单选题Refer to the exhibit. With an IPSec tunnel established between remote Router A and head-end router B, with Compressed Real-Time Protocol (cRTP) configured on the serial interface of Router A, what impact will the cRTP configuration have on the Voice over IP packets flowing through the IPSec tunnel from a Cisco 7960 IP phone?（）A
Twenty bytes of header will be replaced with five bytes. B
If the IPSec transform set includes Authentication Header, the receiving IPSec peer will discard the packets. C
The IPSec packets will be dropped by Router A's compression logic.D
The voice packets will not be compressed.
考题
单选题Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）A
The network administrator faled to save the configuration.B
The configuration register is set to 0x2100.C
The boot system flash command is missing from the configuration.D
The configuraiton register is set to 0x2102.E
The router is configured with the boot system startup command.
热门标签
最新试卷