网友您好, 请在下方输入框内输入要搜索的题目:

题目内容 (请给出正确答案)
单选题
You want to configure switch R1 to propagate VLAN information across the Company network  using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()
A

VTP mode

B

VTP password

C

VTP revision number

D

VTP pruning

E

VTP domain name

F

None of the other alternatives apply


参考答案

参考解析
解析: 暂无解析
更多 “单选题You want to configure switch R1 to propagate VLAN information across the Company network  using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()A VTP modeB VTP passwordC VTP revision numberD VTP pruningE VTP domain nameF None of the other alternatives apply” 相关考题
考题 You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)A. Switch(vlan) mode trunkB. Switch(config) switchport access mode trunkC. Switch(config-if) switchport mode trunkD. Switch(config-if) switchport trunk encapsulation dot1qE. Switch(config) switchport access mode 1F. Switch(vlan) trunk encapsulation dot1q

考题 A new switch is being installed in the Ezonexam network and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this? (Choose all that apply).A.You must set each end of the trunk line to IEEE 802.1e encapsulation.B.You must set the same VTP management domain name on both switches.C.You must set all ports on the two switches as access ports.D.You must configure one of the switches as a VTP server.E.You must use a rollover cable to connect the two switches.

考题 Assuming the default switch configuration,which approach should you use to configure the extended vlan range(1006 through 4094) on a cisco catalyst 3750 series switch?() A. Configure the switch to be in VTP client mode.B. Configure the switch to be in VTP domaint mode.C. Configure the switch to be in VTP transparent mode.D. Configure the switch to be in VTPv2.

考题 You want to allow Router R1 to immediately become the active router if its priority is highest than  the active router fails.  What command would you use if you wanted to configure this? ()A、 en standby preemptB、 standby preempt enableC、 standby preemptD、 hot standby preempt

考题 You are the network administrator of a small Layer 2 network with 50 users. Lately, users have been complaining that the network is very slow. While troubleshooting, you notice that the CAM table of your switch is full, although it supports up to 12,000 MAC addresses. How can you solve this issue and prevent it from happening in the future?()A、Upgrade the switchesB、Configure BPDU guardC、Configure VLAN access listsD、Configure port securityE、Configure Dynamic ARP inspection

考题 Assuming the default switch configuration,which approach should you use to configure the extended vlan range(1006 through 4094) on a cisco catalyst 3750 series switch?()A、Configure the switch to be in VTP client mode.B、Configure the switch to be in VTP domaint mode.C、Configure the switch to be in VTP transparent mode.D、Configure the switch to be in VTPv2.

考题 You are configuring a Cisco multilayer switch for the Company network.  Which command would  you use to configure a port to act as a routed interface?()A、 ip routingB、 switchport mode trunkC、 no switchportD、 switchport trunk native vlan 1E、 None of the other alternatives apply

考题 VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan3 commmand interface configuration mode?()A、The command is accepted and the respective VLAN is added to vlan dat.B、The command is rejected.C、The command is accepted and you must configure the VLAN manually.D、The port turns amber.

考题 As the network technician at Company, you need to configure DHCP snooping on a new switch.   Which three steps are required? ()A、 Configure the switch to insert and remove DHCP relay information (option-82 field) in forwarded  DHCP request messages.B、 Configure DHCP snooping globally.C、 Configure the switch as a DHCP server.D、 Configure DHCP snooping on an interface.E、 Configure all interfaces as DHCP snooping trusted interfaces.F、 Configure DHCP snooping on a VLAN or range of VLANs.

考题 Assuming the default switch configuration,which approach should you use to configure the extended vlanrange(1006 through 4094) on a cisco catalyst 3750 series switch?()A、Configure the switch to be in VTP client mode.B、Configure the switch to be in VTP domaint mode.C、Configure the switch to be in VTP transparent mode.D、Configure the switch to be in VTPv2

考题 You want to configure switch R1 to propagate VLAN information across the Company network  using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()A、VTP modeB、VTP passwordC、VTP revision numberD、VTP pruningE、VTP domain nameF、None of the other alternatives apply

考题 When do you need to configure the P1 interface?()A、 whenever you have an upstream proxyB、 whenever you intend to deploy the L4TM in blocking modeC、 whenever you want to enable the WSA proxyD、 whenever you have a separate management VLAN orsubnetwork

考题 On a Company switch named R1 you configure the following:  iparp inspection vlan 10-12, 15   What is the purpose of this global configuration command made on R1?()A、 Discards ARP packets with invalid IP-to-MAC address bindings on trusted portsB、 Validates outgoing ARP requests for interfaces configured on VLAN 10, 11, 12, or 15C、 Intercepts, logs, and discards ARP packets with invalid IP-to-MAC address bindingsD、 Intercepts all ARP requests and responses on trusted portsE、 None of the other alternatives apply

考题 VLAN 3 is not yet configured on your switch.What happens if you set the switchport access vlan 3 commmand interface configuration mode?()A、The command is accepted and the respective VLAN is added to vlan dat.B、The command is rejected.C、The command is accepted and you must configure the VLAN manually.D、The port turns amber.

考题 If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1,  which trunk mode  would you set the local port to on R1 if you wanted it to respond to requests from its link partner  (R2) and become a trunk? ()A、 AutoB、 NegotiateC、 DesignateD、 No negotiate

考题 A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this?()A、You must set each end of the trunk line to IEEE 802.1e encapsulation.B、You must set the same VTP management domain name on both switches.C、You must set all ports on the two switches as access ports.D、You must configure one of the switches as a VTP server.E、You must use a rollover cable to connect the two switches.

考题 You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.

考题 单选题You want to allow Router R1 to immediately become the active router if its priority is highest than  the active router fails.  What command would you use if you wanted to configure this? ()A  en standby preemptB  standby preempt enableC  standby preemptD  hot standby preempt

考题 多选题You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()AThe switch name must match the workgroup name of the local network.BThe switch must be configured with an IP address and default gateway.CThe remote workstations must have access to the management VLAN of the switch.DCDP must be enabled on the switch so that it can be located by other devices on the network.

考题 单选题VLAN 3 is not yet configured on your switch.What happens if you set the switchport access vlan 3 commmand interface configuration mode?()A The command is accepted and the respective VLAN is added to vlan dat.B The command is rejected.C The command is accepted and you must configure the VLAN manually.D The port turns amber.

考题 多选题A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this?()AYou must set each end of the trunk line to IEEE 802.1e encapsulation.BYou must set the same VTP management domain name on both switches.CYou must set all ports on the two switches as access ports.DYou must configure one of the switches as a VTP server.EYou must use a rollover cable to connect the two switches.

考题 单选题If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1,  which trunk mode  would you set the local port to on R1 if you wanted it to respond to requests from its link partner  (R2) and become a trunk? ()A  AutoB  NegotiateC  DesignateD  No negotiate

考题 单选题Assuming the default switch configuration,which approach should you use to configure the extended vlan range(1006 through 4094) on a cisco catalyst 3750 series switch?()A Configure the switch to be in VTP client mode.B Configure the switch to be in VTP domaint mode.C Configure the switch to be in VTP transparent mode.D Configure the switch to be in VTPv2.

考题 单选题You are implementing basic switch security best practices.  Which of these is a tactic that you can use to mitigate compromises from being launched through the switch?()A Make all ports private VLAN ports.B Place all unused ports in native VLAN 1 until needed.C Proactively configure unused switch ports as access ports.D Disable Cisco Discovery Protocol globally.

考题 单选题On a Company switch named R1 you configure the following:  iparp inspection vlan 10-12, 15   What is the purpose of this global configuration command made on R1?()A  Discards ARP packets with invalid IP-to-MAC address bindings on trusted portsB  Validates outgoing ARP requests for interfaces configured on VLAN 10, 11, 12, or 15C  Intercepts, logs, and discards ARP packets with invalid IP-to-MAC address bindingsD  Intercepts all ARP requests and responses on trusted portsE  None of the other alternatives apply

考题 单选题When do you need to configure the P1 interface?()A  whenever you have an upstream proxyB  whenever you intend to deploy the L4TM in blocking modeC  whenever you want to enable the WSA proxyD  whenever you have a separate management VLAN orsubnetwork

考题 单选题VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan3 commmand interface configuration mode?()A The command is accepted and the respective VLAN is added to vlan dat.B The command is rejected.C The command is accepted and you must configure the VLAN manually.D The port turns amber.