网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
An administrator recently installed a new array controller into a server. When the server is running POST the controller does not appear as present. Which of the following could be the reason for this?（）
- A、The server BIOS firmware is out-of-date.
- B、The server does not have the correct drivers.
- C、The server hard drives have not begun to spin.
- D、The server has too little memory installed.
参考答案
更多 “An administrator recently installed a new array controller into a server. When the server is running POST the controller does not appear as present. Which of the following could be the reason for this?（）A、The server BIOS firmware is out-of-date.B、The server does not have the correct drivers.C、The server hard drives have not begun to spin.D、The server has too little memory installed.” 相关考题
考题
An administrator has just upgraded a server from non-hot plug storage to all hot plug storage. The administrator powers up the server, during POST the RAID controller is recognized but none of the drive lights flash.Which of the following should the administrator do FIRST to troubleshoot the problem?（）A. Check the backplane cabling.B. Check the server BIOS.C. Update the RAID controller firmware.D. Install the latest hard drive firmware
考题
A server administrator recently purchased a new brand of rewritable Blu-ray media and is now having problems backing up data when using the Blu-ray burner installed in the server. Older backup disks still work， but the new media causes the backup software to report burn failures.Which of the following is the BEST solution to resolve the problem？（）A、Update the Blu-ray burner to the latest driversB、Reboot the server and restart the softwareC、Upgrade the firmware on the Blu-ray burnerD、Apply the latest operating service pack
考题
An administrator has just upgraded a server from non-hot plug storage to all hot plug storage. Theadministrator powers up the server， during POST the RAID controller is recognized but none of the drivelights flash. Which of the following should the administrator do FIRST to trouble shoot the problem？（）A、 Check the backplane cabling.B、 Check the server BIOS.C、 Update the RAID controller firmware.D、 Install the latest hard drive firmware.
考题
Memory was recently taken out of a fully functional production server before it wasdecommissioned and added to another server. Upon booting up the server with the additional memory the server emits a series of beeps and fails to POST. Which of the following is MOST likely the problem？（）A、Incompatible memoryB、Memory failureC、The memory is not configuredD、The server BIOS was not configured to accept the additional memory
考题
An administrator has just upgraded a server from non-hot plug storage to all hot plug storage. The administrator powers up the server, during POST the RAID controller is recognized but none of the drive lights flash. Which of the following should the administrator do FIRST to troubleshoot the problem?（）A、Check the backplane cabling.B、Check the server BIOS.C、Update the RAID controller firmware.D、Install the latest hard drive firmware
考题
An administrator notes that after a recent power outage, some open files were corrupted on one affected file server. Which of the following items should the administrator consider to determine the cause of this corruption?（）A、The server's memoryB、The server's RAID controller batteryC、The server's processorD、The server's NIC teaming configuration
考题
An administrator wants to rackmount a new server. Power and network outlets are available and cooling in the room is adequate to support the additional server. The new server is identical to the other servers already installed. Which of the following items should the administrator FIRST verify before installing the server？（）A、HBA is compatible with the SAN fiber switch.B、Update the newly installed server with the latest KVM drivers.C、The UPS will continue to perform as expected with the additional load.D、Verify the server NIC is compatible with the NAS.
考题
An administrator just installed a new RAID controller card into a server. The firmware is current for the controller card. When the server is powered up the administrator notices that the RAID controller card is not recognized during POST. Which of the following is the cause of the problem？（）A、The hard drives were not plugged into the server correctly.B、The controller driver is outdated and needs to be updated from the OEMs website.C、The firmware for the server is too old and does not support the new RAID controller card.D、The cable from the controller to the hard drive backplane is not connected.
考题
An administrator attempts to install the latest security patches for an older server. When the administrator runs the patch installer, the install fails. The administrator tries again, and the installer fails again. Which of the following is the MOST likely reason for this?（）A、The administrator improperly configured the virtual memory settings on the server.B、The administrator is using incorrect patch switches for the install.C、The administrator is trying to install security patches for software that is not installed.D、The administrator is trying to install patches that require hard drive encryption on the server.
考题
An administrator has just installed a new NIC into the server. The system POSTs fine and the NIC is recognized by the OS， but it does not receive an IP address. Which of the following is the MOST likely cause of this？（）A、The NIC is not on the HCL.B、The driver is incorrect on the server.C、The patch cable has not been seated properly.D、The NIC is not seated properly.
考题
An administrator has just installed a web server for the company's Internet site. After bringing the system online, customers notify the administrator that they cannot connect to the server. The administrator tests the web server from a workstation and can access the website. The customers continue to report issues. Which of the following is the MOST likely reason for this?（）A、The server's firewall is misconfigured.B、The server's timeout feature is set incorrectly.C、The web server was not installed properly.D、The company firewall is misconfigured.
考题
Two new servers are purchased and need to be installed to allow sharing of a single external hard drive enclosure. One server is configured as a local file server， and the other as a database server for a different network. The onsite technician notices that when both servers are running at the same time， they each receive SCSI errors. When they are running individually， no errors are reported. Which of the following is the BEST source of information to use for troubleshooting this problem？（）A、 the server vendor’s FAQ websiteB、 the SCSI controller vendor’s user manualC、 the drive enclosure vendor’s user manualD、 the network operating system vendor’s website
考题
A new array of hard drives has been added to an existing server； however， when the server is booted into the Windows OS the new drives fail to appear in My Computer. From which of the following locations can the new storage drives be added？（）A、 Format commandB、 HypervisorC、 Computer ManagementD、 Disk ManagementE、 Virtual Center
考题
An administrator has just finished physically replacing the system board in a Windows domain controller. Which of the following must be done before booting the server back into Windows?（）A、Update the time and date in the BIOS.B、Update the firmware on the SCSI controller.C、Update the firmware to the latest version.D、Configure IPMI on the new board.
考题
After installing a second processor and corresponding heatsink into a server， an administrator notices that the new processor is not showing up during POST. Which of the following could be the cause of this issue？（）A、 The power supply is not sufficient to power the server.B、 The voltage regulator module （VRM） was not installed.C、 The IRQ setting was not set.D、 The DMA setting was not set.
考题
The administrator has just installed a new memory module into the server. Now， the server is not showing the new memory. Which of the following should the administrator perform FIRST？（）A、System rebootB、Reseat the memoryC、Install the latest firmwareD、Install the latest driver
考题
A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）A、Windows cannot be booted from a controller card.B、The hard drive must have Windows reinstalled because a new controller card was installed.C、The SATA controller card was not set as a boot device in the computer BIOS.D、The new controller must have the correct jumper settings for Windows mode.
考题
单选题An administrator attempts to install the latest security patches for an older server. When the administrator runs the patch installer， the install fails. The administrator tries again， and the installer fails again. Which of the following is the MOST likely reason for this？（）A
The administrator improperly configured the virtual memory settings on the server.B
The administrator is using incorrect patch switches for the install.C
The administrator is trying to install security patches for software that is not installed.D
The administrator is trying to install patches that require hard drive encryption on the server.
考题
单选题Two new servers are purchased and need to be installed to allow sharing of a single external hard drive enclosure. One server is configured as a local file server， and the other as a database server for a different network. The onsite technician notices that when both servers are running at the same time， they each receive SCSI errors. When they are running individually， no errors are reported. Which of the following is the BEST source of information to use for troubleshooting this problem？（）A
the server vendor’s FAQ websiteB
the SCSI controller vendor’s user manualC
the drive enclosure vendor’s user manualD
the network operating system vendor’s website
考题
单选题An administrator recently installed a new array controller into a server. When the server is running POST the controller does not appear as present. Which of the following could be the reason for this？（）A
The server BIOS firmware is out-of-date.B
The server does not have the correct drivers.C
The server hard drives have not begun to spin.D
The server has too little memory installed.
考题
单选题After installing a second processor and corresponding heatsink into a server， an administrator notices that the new processor is not showing up during POST. Which of the following could be the cause of this issue？（）A
The power supply is not sufficient to power the server.B
The voltage regulator module （VRM） was not installed.C
The IRQ setting was not set.D
The DMA setting was not set.
考题
单选题An administrator recently installed a new array controller into a server. When the server is running POST the controller does not appear as present. Which of the following could be the reason for this？（）A
The server BIOS firmware is out-of-date.B
The server does not have the correct drivers.C
The server hard drives have not begun to spin.D
The server has too little memory installed.
考题
单选题An administrator has just finished physically replacing the system board in a Windows domain controller. Which of the following must be done before booting the server back into Windows？（）A
Update the time and date in the BIOS.B
Update the firmware on the SCSI controller.C
Update the firmware to the latest version.D
Configure IPMI on the new board.
考题
多选题A new array of hard drives has been added to an existing server; however, when the server is booted into the Windows OS the new drives fail to appear in My Computer. From which of the following locations can the new storage drives be added?（）AFormat commandBHypervisorCComputer ManagementDDisk ManagementEVirtual Center
考题
单选题Memory was recently taken out of a fully functional production server before it wasdecommissioned and added to another server. Upon booting up the server with the additional memory the server emits a series of beeps and fails to POST. Which of the following is MOST likely the problem？（）A
Incompatible memoryB
Memory failureC
The memory is not configuredD
The server BIOS was not configured to accept the additional memory
考题
单选题An administrator notes that after a recent power outage, some open files were corrupted on one affected file server. Which of the following items should the administrator consider to determine the cause of this corruption?（）A
The server's memoryB
The server's RAID controller batteryC
The server's processorD
The server's NIC teaming configuration
考题
单选题An administrator just installed a new RAID controller card into a server. The firmware is current for the controller card. When the server is powered up the administrator notices that the RAID controller card is not recognized during POST. Which of the following is the cause of the problem？（）A
The hard drives were not plugged into the server correctly.B
The controller driver is outdated and needs to be updated from the OEMs website.C
The firmware for the server is too old and does not support the new RAID controller card.D
The cable from the controller to the hard drive backplane is not connected.
热门标签
最新试卷