网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
Which multicast address does RIPv2 use for route updates by default？（）
A
224.0.0.2
B
224.0.0.5
C
224.0.0.9
D
255.255.255.255
参考答案
参考解析
解析：
暂无解析
更多 “单选题Which multicast address does RIPv2 use for route updates by default？（）A 224.0.0.2B 224.0.0.5C 224.0.0.9D 255.255.255.255” 相关考题
考题
Which multicast address does RIPv2 use for route updates by default?()
A.224.0.0.2B.224.0.0.5C.224.0.0.9D.255.255.255.255
考题
Refer to the exhibit. How would you confirm on R1 that load balancing is actually occurring on the default － netw ork (0.0.0.0)?()
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.B. Load balancing does not occur over default networks; the second route will only be used for failover.C. Use an extended ping al ong with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.D. Use the traceroute command to an address that is not explicitly in the routing table.
考题
Which three IP multicast group concepts are true?()
A. If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.B. A router does not have to be a member of a multicast group to recei ve multicast data.C. A router must be a member of a multicast group to send to the group.D. A router does not have to be a member of a multicast group to send to the group.E. If a packet is sent to a multicast group address, all members of the multic ast group will receive it.F. A router must be a member of a multicast group to receive multicast data.
考题
What is the difference between the IPv6 addresses ::／0 and :: ／128? ()
A. ::/0 is the default route, and ::/128 is the unspecified address.B. ::/0 is the unicast address, and ::/128 is the anycast address.C. ::/0 is the anycast address, and ::/128 is the multicast address.D. ::/0 is the unicast address, and ::/12 8 is the multicast address.E. ::/0 is the unspecified address, and ::/128 is the multicast address.F. ::/0 is the anycast address, and ::/128 is the default address.
考题
As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?()
A. TestKSwitch(config)# ip route-default 192.168.1.115B. TestKSwitch(config)# ip default-gateway 192.168.1.115C. TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0D. TestKSwitch(config)# ip default-network 192.168.1.115
考题
You have been asked to configure a default route. Which of the IOS commands mentioned below will accomplish this task?()
A. LTD(config)# ip route 0.0.0.0 0.0.0.0 192.168.15.36B. LTD(config)# ip route 0.0.0.0 192.168.15.36 255.255.255.255C. LTD# ip default-network 0.0.0.0 192.168.15.36 255.255.255.255D. LTD(config)# ip route 0.0.0.0 0.0.0.0 E0E. LTD(config)# ip route 0.0.0.0 255.255.255.255 S0F. LTD(config-router)# ip route 255.255.255.255 0.0.0.0 192.168.15.36
考题
Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()
A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0E. Router(config)# ip route any any e0
考题
Which of the commands below can you use to configure a default route?()
A. TK1(config)# ip route 0.0.0.0 0.0.0.0 E0B. TK1(config)# ip route 0.0.0.0 255.255.255.255 S0C. TK1(config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21D. TK1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21E. TK1(config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255F. TK1# ip default-network 0.0.0.0 192.168.1.21 255.255.255.255
考题
Which configuration command assigns a host route to the CPE workstation address of 192.168.10.1 in a Bridged 1483 network?（）A、ip route 192.168.10.1 255.255.255.255 atm 6/2.1B、ip route 192.168.10.1 255.255.255.252 atm 6/2.1C、add route 192.168.10.1 255.255.255.252 atm 6/2.1D、add route 192.168.10.1 255.255.255.255 atm 6/2.1
考题
Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?（）A、Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0B、Router(config)# ip route 0.0.0.0 255.255.255.255 s0C、Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0D、Router(config)# ip route 0.0.0.0 0.0.0.0 s0E、Router(config)# ip route any any e0
考题
Which three IP multicast group concepts are true?（）A、If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.B、A router does not have to be a member of a multicast group to receive multicast data.C、A router must be a member of a multicast group to send to the group.D、A router does not have to be a member of a multicast group to send to the group.E、If a packet is sent to a multicast group address, all members of the multicast group will rece ive it.F、A router must be a member of a multicast group to receive multicast data.
考题
What is the difference between the IPv6 addresses ：：/0 and ：：/128？（）A、：：/0 is the unspecified address， and ：：/128 is the multicast addressB、：：/0 is the unicast address， and ：：/128 is the anycast addressC、：：/0 is the unicast address， and ：：/128 is the multicast addressD、：：/0 is the anycast address， and ：：/128 is the multicast addressE、：：/0 is the default route， and ：：/128 is the unspecified addressF、：：/0 is the anycast address， and ：：/128 is the default address
考题
Which OSPF LSA type does an ASBR use to originate a default route into an area？ （）A、 LSA 1B、 LSA 3C、 LSA 4D、 LSA 5E、 LSA 7
考题
RIPv2 differs from RIPv1 in that：（）A、it uses multicast address 224.0.0.10，instead of broadcastB、it uses multicast address 224.0.0.9，instead of broadcastC、it can use either multicast or broadcast addresses，instead of just broadcastD、it sends incremental updates，instead of periodic updatesE、it is classless，instead of classfulF、it supports authentication，and RIPv1 does not
考题
Which three statements are true about EIGRP route summarization?（）A、When manual summarization is configured, the router immediately creates a route that points to null0 interfaceB、Manual route summarization is configured in router configuration mode when the router is configured for EIGRP routingC、Manual route summarization is configured on the interfaceD、The ip summary - address eigrp command generates a default route with an administrative distance of 5E、When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routesF、The ip summary - address eigrp command generates a default route with an administrative distance of 90
考题
Which two statements are true about the primary address on an interface? （）A、It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interfaceB、You use the primary address when you have multiple IP addresses belonging to the same subnet on the same intefaceC、It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interfaceD、By default, the primary address on an interface is selected as the nmerically highest local address configured on the interface
考题
Which multicast address does RIPv2 use for route updates by default?（）A、224.0.0.2B、224.0.0.5C、224.0.0.9D、255.255.255.255
考题
单选题Which multicast address does RIPv2 use for route updates by default?（）A
224.0.0.2B
224.0.0.5C
224.0.0.9D
255.255.255.255
考题
单选题What is the difference between the IPv6 addresses ::/0 and :: /128? （）A
::/0 is the default route, and ::/128 is the unspecified address.B
::/0 is the unicast address, and ::/128 is the anycast address.C
::/0 is the anycast address, and ::/128 is the multicast address.D
::/0 is the unicast address, and ::/12 8 is the multicast address.E
::/0 is the unspecified address, and ::/128 is the multicast address.F
::/0 is the anycast address, and ::/128 is the default address.
考题
多选题You have been asked to configure a default route. Which of the IOS commands mentioned below will accomplish this task?（）ALTD(config)# ip route 0.0.0.0 0.0.0.0 192.168.15.36BLTD(config)# ip route 0.0.0.0 192.168.15.36 255.255.255.255CLTD# ip default-network 0.0.0.0 192.168.15.36 255.255.255.255DLTD(config)# ip route 0.0.0.0 0.0.0.0 E0ELTD(config)# ip route 0.0.0.0 255.255.255.255 S0FLTD(config-router)# ip route 255.255.255.255 0.0.0.0 192.168.15.36
考题
多选题Which of the commands below can you use to configure a default route?（）ATK1(config)# ip route 0.0.0.0 0.0.0.0 E0BTK1(config)# ip route 0.0.0.0 255.255.255.255 S0CTK1(config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21DTK1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21ETK1(config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255FTK1# ip default-network 0.0.0.0 192.168.1.21 255.255.255.255
考题
单选题Which OSPF LSA type does an ASBR use to originate a default route into an area？ （）A
LSA 1B
LSA 3C
LSA 4D
LSA 5E
LSA 7
考题
多选题RIPv2 differs from RIPv1 in that：（）Ait uses multicast address 224.0.0.10，instead of broadcastBit uses multicast address 224.0.0.9，instead of broadcastCit can use either multicast or broadcast addresses，instead of just broadcastDit sends incremental updates，instead of periodic updatesEit is classless，instead of classfulFit supports authentication，and RIPv1 does not
考题
单选题Which OSPF LSA type does an ASBR use to originate a default route into an area？（）A
LSA 1B
LSA 3C
LSA 4D
LSA 5E
LSA 7
考题
单选题What is the difference between the IPv6 addresses ：：/0 and ：：/128？（）A
：：/0 is the unspecified address， and ：：/128 is the multicast addressB
：：/0 is the unicast address， and ：：/128 is the anycast addressC
：：/0 is the unicast address， and ：：/128 is the multicast addressD
：：/0 is the anycast address， and ：：/128 is the multicast addressE
：：/0 is the default route， and ：：/128 is the unspecified addressF
：：/0 is the anycast address， and ：：/128 is the default address
考题
单选题As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?（）A
TestKSwitch(config)# ip route-default 192.168.1.115B
TestKSwitch(config)# ip default-gateway 192.168.1.115C
TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0D
TestKSwitch(config)# ip default-network 192.168.1.115
考题
单选题Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?（）A
Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0B
Router(config)# ip route 0.0.0.0 255.255.255.255 s0C
Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0D
Router(config)# ip route 0.0.0.0 0.0.0.0 s0E
Router(config)# ip route any any e0
考题
单选题Which configuration command assigns a host route to the CPE workstation address of 192.168.10.1 in a Bridged 1483 network?（）A
ip route 192.168.10.1 255.255.255.255 atm 6/2.1B
ip route 192.168.10.1 255.255.255.252 atm 6/2.1C
add route 192.168.10.1 255.255.255.252 atm 6/2.1D
add route 192.168.10.1 255.255.255.255 atm 6/2.1
热门标签
最新试卷
