网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
What kind of cable should be used to establish a trunked line between two Catalyst switches?
A．A straight-through cable
B．An EIA/TIA-232 serial cable
C．An auxiliary cable
D．A modem cable
E．A cross-over cable
参考答案
更多 “ What kind of cable should be used to establish a trunked line between two Catalyst switches?A．A straight-through cableB．An EIA/TIA-232 serial cableC．An auxiliary cableD．A modem cableE．A cross-over cable ” 相关考题
考题
What must the Ezonexam network administrator do in order to successfully configure a VLAN trunk between two switches named VE1 and VE2? (Select two answer choices)A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.
考题
Which type of cable should be used to make a connection between the Fa0/0 port on a router and the Fa0/0 port switch?A．Rollover cableB．Console cableC．Crossover cableD．Straight-through cableE．Serial cable
考题
Which two media types support asynchronous transfer mode?()
A.T3B.SONETC.Gigabit-EthernetD.EIA/TIA-232 serial
考题
An administrator is having a hard time adding a new switch to the network. After verifying that allthe ports are configured correctly on each switch, which of the following should the administratorverily NEXT?（）A. Straight-through cable is used to connect both switchesB. Loopback plug is connectedC. Crossover cable is used to connect both switchesD. Cable is a rollover cable
考题
There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the show interface serial 0/0 command is displayed below for each of these routers:From your observations of the above exhibit, what is the underlying cause of the problem?（）A. The loopback is not set.B. The serial cable is faulty.C. The subnet mask is not configured properly.D. The IP address is not configured properly.E. The Layer 2 frame types are not compatible.F. The keepalive setting is not configured properly.
考题
What kind of cable should be used to establish a trunked line between two Catalyst 2950 switches?()
A. a straight-through cableB. an EIA/TIA-232 serial cableC. an auxiliary cableD. a modem cableE. a cross-over cable
考题
What must an administrator do in order to successfully configure a VLAN trunk between two switches?()
A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.
考题
To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met?()
A. Each end of the trunk line must be set to IEEE 802.1E encapsulation.B. The VTP management domain name of both switches must be set the same.C. All ports on both the switches must be set as access ports.D. One of the two switches must be configured as a VTP server.E. A rollover cable is required to connect the two switches together.F. A router must be used to forward VTP traffic between VLANs.
考题
Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has been assigned an IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cable. Attempts to ping between the hosts are unsuccessful. What two things can be done to allow communications between the hosts? （）A. Replace the straight-through cable with a crossover cable.B. Change the subnet mask of the hosts to /25.C. Change the subnet mask of the hosts to /26.D. Change the address of Workstation A to 192.0.2.15.E. Change the address of Workstation B to 192.0.2.111.
考题
For which type of connection should a straight－through cable be used?()
A.switch to switchB.switch to hubC.switch to routerD.hub to hubE.router to PC
考题
Workstation A has been assigned an IP address of 192.0.2.24/28. Workstation B has beenassigned an IP address of 192.0.2.100/28. The two workstations are connected with a straight-through cablE.Attempts to ping between the hosts are unsuccessful. What two things can be done to allow communications between the hosts? （）A.Replace the straight-through cable with a crossover cableB.Change the subnet mask of the hosts to /25C.Change the subnet mask of the hosts to /26D.Change the address of Workstation A to 192.0.2.15E.Change the address of Workstation B to 192.0.2.111
考题
Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）A、show interfaces serial 0/0B、show running-configC、show versionD、show controllers serial 0/0E、show ip interfaceF、show line serial 0/0
考题
For which type of connection should a straight-through cable be used?（）A、switch to switchB、switch to hubC、switch to routerD、hub to hubE、router to PC
考题
What must an administrator do in order to successfully configure a VLAN trunk between two switches?（）A、Set each end of the trunk line to IEEE 802.1Q encapsulation.B、Set the same VTP management domain name on both switches.C、Set all ports on the two switched as access ports.D、Configure one of the two switches as a VTP server.E、Connect the two switches using a rollover cable.F、Use a router to forward VTP traffic between the VLANs.
考题
Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning session， it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network. What should be done to ensure the serial network will function with HACMP heartbeats？（） A、 Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.B、 Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.C、 Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.D、 Verify with IBM support which native serial ports for the server model can be used for HACM pheartbeats.
考题
Which type of cable should be used to make a connection between the Fa0/0 port on a router and the Fa0/0 port switch?（）A、Rollover cableB、Console cab leC、Crossover cableD、Straight-through cableE、Serial cable
考题
What kind of cable should be used to establish a trunked line between two Catalyst 2950 switches?（）A、a straight-through cableB、an EIA/TIA-232 serial cableC、an auxiliary cableD、a modem cableE、a cross-over cable
考题
A network administrator needs to add an additional connection to a room. The administrator adds a new Ethernet switch and must connect it to an existing switch. Which cable type should be used to connect the two switches?（）A、CAT3 cableB、Serial cableC、Crossover cableD、Rollover cable
考题
An administrator is having a hard time adding a new switch to the network. After verifying that allthe ports are configured correctly on each switch, which of the following should the administratorverily NEXT?（）A、Straight-through cable is used to connect both switchesB、Loopback plug is connectedC、Crossover cable is used to connect both switchesD、Cable is a rollover cable
考题
Which of the following should be used to check a serial port for functionality?（）A、Loopback plugB、Toner probeC、MultimeterD、Cable tester
考题
When making a serial connection between two Windows 2000 machines， which type of cable is needed for proper communications？（）A、RG-59 coaxial cableB、RS-232 Null Modem cableC、telephone cableD、UTP CAT5 patch cable
考题
单选题For which type of connection should a straight-through cable be used?（）A
switch to switchB
switch to hubC
switch to routerD
hub to hubE
router to PC
考题
单选题Company.com wishes to use HACMP on two IBM eServer pSeries servers. During the planning session， it was decided to use the native serial ports s1 or s2 for a non-IP heartbeat network. What should be done to ensure the serial network will function with HACMP heartbeats？（）A
Use either s1 or s2 port configured as a TTY interface with a NULL Modem cable.B
Use the s2 serial port on each system configured as a TTY interface with a NULL modem cable.C
Use the s1 port on each system configured as a TTY interface with a standard serial modemcable.D
Verify with IBM support which native serial ports for the server model can be used for HACM pheartbeats.
考题
单选题Which type of cable should be used to make a connection between the Fa0/0 port on a router and the Fa0/0 port switch?（）A
Rollover cableB
Console cab leC
Crossover cableD
Straight-through cableE
Serial cable
考题
单选题A network administrator needs to add an additional connection to a room. The administrator adds a new Ethernet switch and must connect it to an existing switch. Which cable type should be used to connect the two switches?（）A
CAT3 cableB
Serial cableC
Crossover cableD
Rollover cable
考题
单选题What kind of cable should be used to establish a trunked line between two Catalyst 2950 switches?（）A
a straight-through cableB
an EIA/TIA-232 serial cableC
an auxiliary cableD
a modem cableE
a cross-over cable
考题
单选题Which command can be used to determine the type of cable attached to the Serial 0/0 interface on a router?（）A
show interfaces serial 0/0B
show running-configC
show versionD
show controllers serial 0/0E
show ip interfaceF
show line serial 0/0
热门标签
最新试卷