网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Refer to the exhibit. There are two sites connected across WAN links. All intersite and intrasite links always have the same routing metric. The network administrator sees only the top routers and links being used by hosts at both LAN A and LAN B. What would be two suggestions to load-balance the traffic across both WAN links？（）
- A、 Make HSRP track interfaces between the edge and core routers.
- B、 Replace HSRP with GLBP. 用GLBP替换HSRP
- C、 Add crossed intrasite links： R1-R4， R2-R3， R5-R8， and R6-R7.
- D、 Make R3 and R8 have lower HSRP priority than R1 and R7.
- E、 Replace HSRP with VRRP
参考答案
更多 “Refer to the exhibit. There are two sites connected across WAN links. All intersite and intrasite links always have the same routing metric. The network administrator sees only the top routers and links being used by hosts at both LAN A and LAN B. What would be two suggestions to load-balance the traffic across both WAN links？（）A、 Make HSRP track interfaces between the edge and core routers.B、 Replace HSRP with GLBP. 用GLBP替换HSRPC、 Add crossed intrasite links： R1-R4， R2-R3， R5-R8， and R6-R7.D、 Make R3 and R8 have lower HSRP priority than R1 and R7.E、 Replace HSRP with VRRP” 相关考题
考题
What does a router do?()
A.Routes traffic down alternative paths and connects the local-area network (LAN) to the wide- area network (WAN)B.Reads Media Access Control (MAC) addresses to forward messages to the correct location and connects the local-area network (LAN) to the wide-area network (WAN)C.Stores data on the network and connects the local-area network (LAN) to the wide-area network (WAN)D.Broadcasts data to all devices that are connected to it across the local-area network (LAN) and wide-area network (WAN)
考题
Refer to the exhibit. BigBids Incorporated is a worldwide auction provider. The network uses EIGRP as its routing protocol throughout the corporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all - links command, answer the administrator‘s questions.Which three networks is the router at 172.17.10.2 directly connected to?（）A. 172.17.0.0/30B. 172.17.1.0/24C. 172.17.2.0/24D. 172.17.3 .0/25E. 172.17.3.128/25F. 172.17.10.0/24
考题
Your network has a mixture of Fast Ethernet and Gigabit Ethernet links. What needs t o be done to ensure optimal data routing when using OSPF?()
A. Nothing. OSPF will determine the most optimal path for routing data by default.B. Adjust the hello and dead timers for more rapid detection of link failures.C. Increase the reference - bandw idth used to calculate the interface default metrics, on all routers in your network.D. Set the priority values on every broadcast interface to ensure that the designated and backup designated routers are the routers with the most processor and memory resources.
考题
Refer to the exhibit. In a redundant hub - and - spoke deployment using EIGRP, what feature can be used to ensure that routers C through F are not used as transit routers for data traveling from router B to network 10.1.1.0? Select the best response.（）A. Use address summarization at routers C, D, E, and FB. Use the EIGRP Stub featu re on routers C, D, E, and FC. Use passive - interface on the spoke links in routers A and BD. Change the administrative distance in routers A and B for routes learned from routers C, D, E,and F
考题
Refer to the above exhibit. Why is the 140.140.0.0 network not used as the gateway of last resort even though it is configured first?()
A.The last default - network statement will always be preferred.B.A route to the 140.140.0.0 network does not exist in the routing table.C.Default - network selection will always prefer the statement with the lowest IP address.D.A router will load balance across multiple default - networks; repeatedly issuing the show ip route command would show the gateway of last resort changing between the two networks.
考题
Refer to the exhibit.The actual speed of the serial links between R2 and R3 are 256 kb/s and 512k b/s respectively. When configuring EIGRP on routers R2 and R3, the network administrator configured the bandwidth of both serial interfaces to 512 kb/s. What will be the effect?（）A. EIGRP will overutilize the 512 kb/s link.B. The interface delay value used in the EIGRP metric calculation will be inaccurate on the 256k b/s serial interface.C. The amount of bandwidth used for EIGRP routing protocol traffic on the 256 kb/s link can become excessive.D. EIGRP can load balance between the two serial links only if the variance is set to 2 or higher.E. Unequal cost load balancing will be disabled.
考题
Refer to the exhibit. The Route.com company is running EIGRP between all the r outers. Currently, if one of the LAN links (LAN1 or LAN2) at the headquarters flaps (goes up and down), the HQRTR1 and HQ - RTR2 routers will experience high CPU usage and have a long EIGRP convergence time. As the new network administrator, you are asked to investigate this situation and determine if there is a quick way to resolve this issue. Which is the most important thing that you can quickly verify first to resolve this issue?（）A. Verify that the bandwidth setting on all WAN links is correct.B. Verify that the HQ - RTR1 and HQ - RTR2 routers are configured to send only a default route to all the spoke routers.C. Verify that the HQ - RTR1 and HQ - RTR2 routers are configured for EIGRP Nonstop Forwarding.D. Verify that all the spoke routers are co nfigured for autosummarization.E. Verify that all the spoke routers are configured as EIGRP stub.
考题
Refer to the exhibit. You are the network administrator of the Route.com company. You have been tasked to implement a hub and spoke EIGRP topology over Frame Relay to provide connectivity between the networks at headquarters and all 300 spokes. Before you begin the actual implementation, which three pieces of information are more important to know than the others?（）A. the Committed Information Rate of all the Frame Relay PVCsB. the Cisco IOS version running on all the routersC. the router model number of all the spoke routersD. the number of HQ networks connected behind the headquarter routersE. the routing policy, such as whether or not the spokes can be used as backup transient point between the two headquarter routers
考题
What are two characteristics of the OSPF process identifier?()
A. It is needed to identify a unique instance of an OSPF database.B. It is an optional parameter only necessary if multiple OSPF processes are used.C. It is locally significant.D. It is globally insignificantE. All routers in the same OSPF area must have the same process ID to exchange routing information.
考题
What are the different characteristics of distance vector and link state routing protocols?()
A. Distance vector protocols send the entire routing table to directly connected neighbors.B. Distance vector protocols are responsible for sending updates to all networks listed in the routing table.C. Link state protocols are responsible for sending the entire routing table to the whole network.D. Link state protocols send updates regarding their own links status to all other routers on the network.E. None of the above
考题
What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network?()
A. A hub router prevents routes from being advertised to the remote router.B. Only remote routers are configured as stubs.C. Stub routers are not queried for routes.D. Spoke routers connected to hub routers answer the route queries for the stub router.E. A stub router should have only EIGRP hub routers as neighbors.F. EIGRP stub routing should be used on hub routers only.
考题
The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?（）A.8B.6C.30D.32E.14F.16
考题
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?()
A.As numbers must be changed to match on all the routers.B.Loopback interface must be configured so a DR is elected.C.The no auto-summary command is needed on Router A and Router C.D.Router B needs to have two network statements, one for each connected network.
考题
If the OSPF protocol is used to connect customer edge （CE） routers to service provider edge（PE） routers in the VPN backbone， which two options best describe the use of SHAM links？（）A、A sham-link is created between any twoo VPN sites that belong to the same OSPF area and share an OSPF backdoor linkB、A sham-link is seen as an intra-area link between PE routers，an OSPF adjacency is created and data base is exchangedC、A SHAM link is created between two directly connected PE routers so that it is preferred over the low speed backdoor doorD、A SHAM link is part of OSPF network of MPLS-VPN provider
考题
The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?（）A、8B、6C、30D、32E、14F、16
考题
What are two characteristics of the OSPF process identifier?（）A、It is needed to identify a unique instance of an OSPF database.B、It is an optional parameter only necessary if multiple OSPF processes are used.C、It is locally significant.D、It is globally insignificantE、All routers in the same OSPF area must have the same process ID to exchange routing information.
考题
What does a router do?（）A、Routes traffic down alternative paths and connects the local-area network (LAN) to the wide- area network (WAN)B、Reads Media Access Control (MAC) addresses to forward messages to the correct location and connects the local-area network (LAN) to the wide-area network (WAN)C、Stores data on the network and connects the local-area network (LAN) to the wide-area network (WAN)D、Broadcasts data to all devices that are connected to it across the local-area network (LAN) and wide-area network (WAN)
考题
In a switched LAN network, what is the Spanning-Tree algorithm used for?（）A、It is used to provide a mechanism for routing updates in switched environments.B、It is used to prevent routing loops in networks with redundant routes.C、It is used to prevent switching loops in networks with redundant switched routes.D、It is used to manage, the addition, deletion, and naming of VLANs across multiple switches.E、It is used to segment a network into multiple collision domains.F、None of the above.G、All of the above are functions of STP.
考题
What are the different characteristics of distance vector and link state routing protocols?（）A、Distance vector protocols send the entire routing table to directly connected neighbors.B、Distance vector protocols are responsible for sending updates to all networks listed in the routing table.C、Link state protocols are responsible for sending the entire routing table to the whole network.D、Link state protocols send updates regarding their own links status to all other routers on the network.E、None of the above
考题
Which two are advantages of static routing when compared to dynamic routing?（）A、Security increases because only the network administrator may change the routing tables.B、Configuration complexity decreases as network size increases.C、Routing updates are automatically sent to neighbors.D、Route summarization iscompued automatically by the router.E、Routing traffic load is reduced when used in stub network links.F、An efficient algorithm is used to build routing tables,using automatic updates.G、Routing tables adapt automatically to topology changes.
考题
Which of the following is the purpose of QoS?（）A、Load balance traffic across multiple LAN and WAN links.B、Increase speed of network traffic.C、Classify, mark, and prioritize traffic on WAN and LAN linksD、Guarantee traffic delivery.
考题
You are designing a strategy to install the new scheduling application. Which two actions should you perform？（）A、 Assign the scheduling application package to the Instructor OU.B、 Publish the scheduling application package to the Instructor OU.C、 Ensure that the scheduling application can install across slow WAN links.D、 Prevent the scheduling application from installing across slow WAN links.
考题
单选题Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A
As numbers must be changed to match on all the routers.B
Loopback interface must be configured so a DR is elected.C
The no auto-summary command is needed on Router A and Router C.D
Router B needs to have two network statements, one for each connected network.
考题
多选题If the OSPF protocol is used to connect customer edge （CE） routers to service provider edge（PE） routers in the VPN backbone， which two options best describe the use of SHAM links？（）AA sham-link is created between any twoo VPN sites that belong to the same OSPF area and share an OSPF backdoor linkBA sham-link is seen as an intra-area link between PE routers，an OSPF adjacency is created and data base is exchangedCA SHAM link is created between two directly connected PE routers so that it is preferred over the low speed backdoor doorDA SHAM link is part of OSPF network of MPLS-VPN provider
考题
多选题What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）AA hub router prevents routes from being advertised to the remote router.BOnly remote routers are configured as stubs.CStub routers are not queried for routes.DSpoke routers connected to hub routers answer the route queries for the stub router.EA stub router should have only EIGRP hub routers as neighbors.FEIGRP stub routing should be used on hub routers only.
考题
多选题Which two are advantages of static routing when compared to dynamic routing?（）ASecurity increases because only the network administrator may change the routing tables.BConfiguration complexity decreases as network size increases.CRouting updates are automatically sent to neighbors.DRoute summarization iscompued automatically by the router.ERouting traffic load is reduced when used in stub network links.FAn efficient algorithm is used to build routing tables,using automatic updates.GRouting tables adapt automatically to topology changes.
考题
多选题Refer to the exhibit. There are two sites connected across WAN links. All intersite and intrasite links always have the same routing metric. The network administrator sees only the top routers and links being used by hosts at both LAN A and LAN B. What would be two suggestions to load-balance the traffic across both WAN links？（）AMake HSRP track interfaces between the edge and core routers.BReplace HSRP with GLBP. 用GLBP替换HSRPCAdd crossed intrasite links： R1-R4， R2-R3， R5-R8， and R6-R7.DMake R3 and R8 have lower HSRP priority than R1 and R7.EReplace HSRP with VRRP
热门标签
最新试卷