网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24／29. which statement explains the reason for this issue?()
A.The address is abroadcast address.
B.The Ehernet interface is faulty.
C.VLSM-capable routing protocols must be enable first on the router.
D.This address is a network address.
参考答案
更多 “ A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24／29. which statement explains the reason for this issue?() A.The address is abroadcast address.B.The Ehernet interface is faulty.C.VLSM-capable routing protocols must be enable first on the router.D.This address is a network address. ” 相关考题
考题
While troubleshooting an issue in the Ezonexam LAN you notice that a network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?A. This is an Ethernet port operating at half duplexB. This is an Ethernet port operating at full duplexC. This is a port on a network interface card in a PCD. This is 10 MB/s switch portE. This is a 100 MB/s switch portF. None of the above
考题
You would like to operate IS－IS on interface atm 6／0.33 with an IP address of 192.168.1.1／24.Which set of commands accomplishes this?()
A. router isis network 192.168.1.0 0.0.0.255B. router isis network 192.168.1.0 255.255.255.0C. interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 router isisD. interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 ip router isis
考题
Refer to the exhibit. Which statement is co rrect regarding the router configuration shown? ()
A. The router will rebroadcast any DHCP requests received by this interface out to all interfaces included in the ip helper - address commands.B. The router will rebroadcast any UDP broadcasts received by this interface out to all interfaces included in the ip helper - address commands.C. The router will unicast any DHCP requests received by this interface out to all addresses included in the ip helper - address commands.D. This configuration will not do anything because the ip helper - address command needs to also be applied to the 192.168.23.1 IP address.
考题
Refer to the exhibit. A network administrator has configured DHCP services on the router asshown. DHCP clients connected to the FastEthernet0/0 interface are working properly. DHCP clients connected to the FastEthernet0/1 interface are not receiving addresses.Which two statements contain recommendations that will solve the problem?（）A.The network shown in the output under the ip dhcp pool Central command should be changed to network 10.10.0.0 with a mask of 255.255.255.0B.A second DHCP pool for network 10 .10.0.0/24 should be configuredC.An ip dhcp excluded - address global configuration command for network 10.10.0.0/24 should be issuedD.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/0 c onfigurationE.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/1 configuration
考题
You‘re working at TestKing as a network administrator when your MCSE assistant calls you for help. He has attempted to configure Router TK1 and incorrectly configured the router interface with a subnet broadcast address. You have to correct this by first removing the incorrect IP address and then re-entering the first usable IP address of the same subnet.How will you do this?（）A.B.C.D.E.
考题
An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF?()
A. Ensure that an interface has been configured with an IP addressB. Ensure that IP classless is enabledC. Ensure that the interfaces can ping their directly connected neighborsD. Ensure that an interface has been configured with an IP address and is up
考题
On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?()
A. The IP address of the first Fast Ethernet interface.B. The IP address of the console management interface.C. The highest IP address among its active interfaces.D. The lowest IP address among its active interfaces.E. There will be no router ID until a loopback interface is configured.
考题
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）A. Issue the show ip route command on Router AB. Issue the show ip route command on Router BC. Issue the show cdp neighbors command on Router BD. Issue the show cdp neighbors detail command on Router CE. Issue the show arp command on Router AF. Issue the show arp command on Router B
考题
The OSPF process has been started and the networks have been configured for Area 0 as shown in the diagram. The network administrator has several options for configuring RouterB to ensure that it will be preferred as the designated router (DR) for the 172.16.1.0 /24 LAN segment. What configuration tasks could be used to establish this preference (Choose three.)（）。A.Configure the priority value of the Fa0/0 interface of RouterB to a higher value than any other interface on the Ethernet network.B.Change the router id of Router B by assigning the IP address 172.16.1.130/24 to the Fa0/0 interface of RouterB.C.Configure a loopback interface on RouterB with an IP address higher than any IP address on the other routers.D.Change the priority value of the Fa0/0 interface of RouterB to zero.E.Change the priority values of the Fa0/0 interfaces of RouterA and RouterC to zero.F.No further configuration is necessary.
考题
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router.How should the network administrator configure the serial interface of the main office router to make the connection?（）A.B.C.D.
考题
A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24/29. which statement explains the reason for this issue？（）A、The address is abroadcast address.B、The Ehernet interface is faulty.C、VLSM-capable routing protocols must be enable first on the router.D、This address is a network address.
考题
A network administrator has configured access list 172 to prevent Telnet and ICMP traffic from reaching a server with the address if 192.168.13.26. Which command can the administrator issue to verify that the access list is working properly?（）A、Router# ping 192.168.13.26B、Router# debug access-list 172C、Router# show open ports 192.168.13.26D、Router# show access-listE、Router# show ip interface
考题
You are the administrator of a Windows 2000 network. You install Windows 2000 Professional on a new computer and configure the TCP/IP settings to have a static IP address. While testing network connectivity from the new computer, you discover an error in the DNS server address that is configured in the TCP/IP settings. You configure the correct DNS server address, which is 10.1.1.5. However, you are still unable to successfully connect to network resources by name. You run the IPconfig/all command. The results indicate that the DNS server address is now configured as 0.0.0.0 You need to ensure that the computer can connect to network resources by name. What should you do?（）A、Stop and restart the DNS Client service.B、Add 10.1.1.5 to the DNS server list on the TCP/IP Advanced Properties tab.C、Add an A （host） record for the computer to the DNS server’s zone file.D、Configure your DHCP server to have a DNS server address of 10.1.1.5.
考题
A network administrator receives an error message while tring to configure the Ethernet interface of arouter with IP address 10.24.24.24/29.which statement explains the reason for this issue？（）A、The address is a broadcast addressB、The Ehernet interface is faultyC、VLSM-capable routing protocols must be enable first on the router.D、This address is a network address.
考题
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）A、Issue the show ip route command on Router AB、Issue the show ip route command on Router BC、Issue the show cdp neighbors command on Router BD、Issue the show cdp neighbors detail command on Router CE、Issue the show arp command on Router AF、Issue the show arp command on Router B
考题
A BGP router is configured as shown below： interface ethernet 0 ip address 10.10.10.1 255.255.0.0! int serial 0 ip address 172.16.1.1 255.255.255.252! router bgp 65001 neighbor 192.168.1.1 remote-as 65002 Based on the above configuration， which of the following BGP statements would inject the10.10.0.0/16 prefix into the BGP routing table？（）A、network 10.0.0.0B、network 10.10.0.0 mask 255.255.0.0C、network 10.10.10.1 mask 255.255.255.255D、network 10.10.10.0 mask 255.255.255.0E、network 10.0.0.0 mask 255.255.0.0
考题
A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24/29.which statement explains the reason for this issue?（）A、The address is a broadcast addressB、The Ehernet interface is faultyC、VLSM-capable routing protocols must be enable first on the router.D、This address is a network address.
考题
给了两段documentation里的描述，问这个时候发哪种类型的ICMP包。 The interface on which the packet comes into the router is the same interface on which the packet gets routed out. The subnet or network of the source IP address is on the same subnet or network of the next-hop IP address of the routed packet.
考题
You would like to operate IS-IS on interface atm 6/0.33 with an IP address of 192.168.1.1/24. Which set of commands accomplishes this?（）A、router isis network 192.168.1.0 0.0.0.255B、router isis network 192.168.1.0 255.255.255.0C、interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 router isisD、interface atm 6/0.33 ip address 192.168.1.1 255.255.255.0 ip router isis
考题
You are the network administrator for Company. Company has recently upgraded its network to a 100Mbps standard and you are now in the process of removing all the old adapter and installing a new Token Ring network adapter into the Windows 2000 Professional computer. On the first computer you install the new hardware and configure the static TCP/IP protocol settings to be the same as they were for the previously installed network adapter. When you restart the computer, however, you cannot access the network. You try to ping your network adapter's TCP/IP address locally. You receive the following error message: "Request timed out." You want to enable the computer to communicate on the new network. What should you do? （）A、Enable DHCP in the TCP/IP properties.B、Replace the Token Ring network adapter with an Ethernet network adapter.C、Configure a different TCP/IP address on the same subnet.D、Configure a valid DNS Server in the TCP/IP properties.
考题
单选题A network administrator receives an error message while tring to configure the Ethernet interface of arouter with IP address 10.24.24.24/29.which statement explains the reason for this issue？（）A
The address is a broadcast addressB
The Ehernet interface is faultyC
VLSM-capable routing protocols must be enable first on the router.D
This address is a network address.
考题
单选题An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF？（）A
Ensure that an interface has been configured with an IP addressB
Ensure that IP classless is enabledC
Ensure that the interfaces can ping their directly connected neighborsD
Ensure that an interface has been configured with an IP address and is up
考题
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A
physical layer issuesB
no spanning tree loopsC
use of non-default HSRP timersD
failure to set the command standby 35 preempt
考题
单选题A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?（）A
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#no shutB
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)#no shutC
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation frame-relay Main(config-if)#authenication chap Main(config-if)#no shutD
Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ppp Main(config-if)#no shut
考题
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）A
physical layer issuesB
no spanning tree loopsC
use of non-default HSRP timersD
failure to set the command standby 35 preempt
考题
单选题On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?（）A
The IP address of the first Fast Ethernet interface.B
The IP address of the console management interface.C
The highest IP address among its active interfaces.D
The lowest IP address among its active interfaces.E
There will be no router ID until a loopback interface is configured.
考题
单选题A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24/29.which statement explains the reason for this issue?（）A
The address is a broadcast addressB
The Ehernet interface is faultyC
VLSM-capable routing protocols must be enable first on the router.D
This address is a network address.
考题
单选题A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24/29. which statement explains the reason for this issue？（）A
The address is abroadcast address.B
The Ehernet interface is faulty.C
VLSM-capable routing protocols must be enable first on the router.D
This address is a network address.
热门标签
最新试卷