网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?（）
A
The IP address of the first Fast Ethernet interface.
B
The IP address of the console management interface.
C
The highest IP address among its active interfaces.
D
The lowest IP address among its active interfaces.
E
There will be no router ID until a loopback interface is configured.
参考答案
参考解析
解析：
暂无解析
更多 “单选题On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?（）A The IP address of the first Fast Ethernet interface.B The IP address of the console management interface.C The highest IP address among its active interfaces.D The lowest IP address among its active interfaces.E There will be no router ID until a loopback interface is configured.” 相关考题
考题
某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16 Cisco路由器的正确配置是A．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0B．Router (config) #router ospf 63 Router (config-router) # network 169.111.0.0 255.255.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0C．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0D．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 0.0.255.255
考题
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
考题
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.What could be the cause of this problem?（）A. OSPF authentication errors between some of the routersB. Two routers have the same OSPF router IDC. Issues with mistuned OSPF timersD. OSPF LSA pacing issues between some of the routersE. OSPF neighbor adjacency problems between some of the routers
考题
Which command enables OSPF for IPv6?()
A. router ospf ipv6 process - idB. ipv6 ospf process - idC. router ospf process - idD. ipv6 router ospf process - id
考题
Open Shortes t Path First (OSPF) is a routing protocol developed for Internet Protocol (IP) networks by the Interior Gateway Protocol (IGP) working group of the Internet Engineering Task Force (IETF).Which two statements best describe the OSPF link - state routing pro tocol?（）A. OSPF sends updates every 10 secondsB. OSPF sends triggered updates when a network change occursC. When a link state is changed, the router that detected the change creates a link - state advertisement (LSA) and propagates it to all OSPF devices using the 224.0.0.6 multicast addressD. OSPF sends summaries of individual link- state entries every 30 minutes to ensure LSDB synchronization
考题
On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?()
A. The IP address of the first Fast Ethernet interface.B. The IP address of the console management interface.C. The highest IP address among its active interfaces.D. The lowest IP address among its active interfaces.E. There will be no router ID until a loopback interface is configured.
考题
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?()
A.Router(config)#router ospf 1B.Router(config)#router ospf 0C.Router(config)#router ospf area 0D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E.Router(config-router)#network 192.168.16.0 0.0.0.255 0F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
考题
Which command enables OSPF for IPv6?（）A、router ospf ipv6 process - idB、ipv6 ospf process - idC、router ospf process - idD、ipv6 router ospf process - id
考题
Which description regarding OSPF Network LSAs is correct?（）A、They are originated by Area Border Router and are sent into a single area to advertise an Autonomous System Border Router.B、They are originat ed by Area Border Routers and are sent into a single area to advertise destinations outside that area.C、They are originated by the DR on every multi - access network. They include all attached routers including the DR itself.D、They are originated by every router in the OPSF network. They include all routers on the link, interfaces, the cost of the link, and any known neighbor on the link.
考题
Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）A、Router（config）#router ospf 1B、Router（config）#router ospf 0C、Router（config）#router ospf area 0D、Router（config-router）#network 192.168.16.0 0.0.0.255 area 0E、Router（config-router）#network 192.168.16.0 0.0.0.255 0F、Router（config-router）#network 192.168.16.0 255.255.255.0 area 0
考题
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds. What could be the cause of this problem?（）A、OSPF authentication errors between some of the routersB、Two routers have the same OSPF router IDC、Issues with mistuned OSPF timersD、OSPF LSA pacing issues between some of the routersE、OSPF neighbor adjacency problems between some of the routers
考题
Open Shortes t Path First (OSPF) is a routing protocol developed for Internet Protocol (IP) networks by the Interior Gateway Protocol (IGP) working group of the Internet Engineering Task Force (IETF). Which two statements best describe the OSPF link - state routing pro tocol?（）A、OSPF sends updates every 10 secondsB、OSPF sends triggered updates when a network change occursC、When a link state is changed, the router that detected the change creates a link - state advertisement (LSA) and propagates it to all OSPF devices using the 224.0.0.6 multicast addressD、OSPF sends summaries of individual link- state entries every 30 minutes to ensure LSDB synchronization
考题
管理员想在MSR路由器上配置OSPF路由优先级值为60，则下列哪条命令是正确的？（）A、[Router]ospf preference 60B、[Router]preference 60C、[Router-ospf-1]ospf preference 60D、[Router-ospf-1]preference 60
考题
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
考题
What is the purpose of the OSPF router ID in a OR/BOR election?（）A、It is used with the OSPF priority values to determine which OSPF router will become the DR or BOR in a point-to-point networkB、It is used with the OSPF priority values to determine which interface will be used to form a neighbor relationship with another OSPF routerC、It is used with the OSPF priority values to determine which router will become the DR or BOR in a multi access networkD、It is used to determine which interfaces will send Hello packets to neighboring OSPF routers
考题
Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）A、Router(config-router)# network 192.168.10.0 0.0.0.255 0B、Router(config-router)# network 192.168.10.0 0.0.0.255 area 0C、Router(config-router)# network 192.168.10.0 255.255.255.0 area 0D、Router(config)# router ospf 0E、Router(config)# router ospf 1
考题
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）A、Only the router A loopback interface is parti cipating in the OSPF routing processB、None of the router A interfaces are participating in the OSPF routing processC、Router A is using the loopback interface IP address as its OSPF router IDD、Router A does not have any reachable OSPF neighbors
考题
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
考题
什么命令序列将配置一个路由器运行OSPF，并添加网络10.1.1.0/24 area0？（）A、router ospf area 0 network 10.1.1.0 255.255.255.0 area 0B、router ospf network 10.1.1.0 0.0.0.255C、router ospf 1 network 10.1.1.0 0.0.0.255 area 0D、router ospf area 0 network 10.1.1.0 0.0.0.255 area 0E、router ospf network 10.1.1.0 255.255.255.0 area 0F、router ospf 1 network 10.1.1.0 0.0.0.255
考题
多选题Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）ARouter(config-router)# network 192.168.10.0 0.0.0.255 0BRouter(config-router)# network 192.168.10.0 0.0.0.255 area 0CRouter(config-router)# network 192.168.10.0 255.255.255.0 area 0DRouter(config)# router ospf 0ERouter(config)# router ospf 1
考题
单选题What type of OSPF router is responsible for redistributing routes into OSPF?（）A
ABRB
ASBRC
internal routerD
backbone router
考题
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ATestKingRouter(config)# router ospf 0BTestKingRouter(config)# router ospf 1CTestKingRouter(config)# router ospf area 0DTestKingRouter(config)# network 192.168.16.0 0.0.0.255 0ETestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0FTestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
考题
单选题You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds. What could be the cause of this problem?（）A
OSPF authentication errors between some of the routersB
Two routers have the same OSPF router IDC
Issues with mistuned OSPF timersD
OSPF LSA pacing issues between some of the routersE
OSPF neighbor adjacency problems between some of the routers
考题
单选题Which description regarding OSPF Network LSAs is correct?（）A
They are originated by Area Border Router and are sent into a single area to advertise an Autonomous System Border Router.B
They are originat ed by Area Border Routers and are sent into a single area to advertise destinations outside that area.C
They are originated by the DR on every multi - access network. They include all attached routers including the DR itself.D
They are originated by every router in the OPSF network. They include all routers on the link, interfaces, the cost of the link, and any known neighbor on the link.
考题
多选题Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
考题
多选题Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
考题
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ARouter(config)#router ospf 1BRouter(config)#router ospf 0CRouter(config)#router ospf area 0DRouter(config-router)#network 192.168.16.0 0.0.0.255 area 0ERouter(config-router)#network 192.168.16.0 0.0.0.255 0FRouter(config-router)#network 192.168.16.0 255.255.255.0 area 0
热门标签
最新试卷