网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）
A
The HSRP priority for router R1 will increase to 200.
B
Router R1 will become the standby router if the priority drops below 50.
C
The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.
D
Router R1 will wait 50 seconds before attempting to preempt the active router.
参考答案
参考解析
解析：
暂无解析
更多 “单选题You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A The HSRP priority for router R1 will increase to 200.B Router R1 will become the standby router if the priority drops below 50.C The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D Router R1 will wait 50 seconds before attempting to preempt the active router.” 相关考题
考题
A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers.Which of the following could be used to prevent potential routing loops in this design?（）A. Using an iBGP mesh inside the Enterprise coreB. Configuring default routes in the Enterprise pointing to both R1 and R2C. Redistributing BGP routes into the Enterprise IGPD. Tunneling the packets for the i BGP connection between R1 and R2
考题
Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A. 22B. 11C. 1D. None
考题
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
考题
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? ()
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
考题
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
考题
Refer to the exhibit. The company uses EIGRP as the routing protocol. What path will packets take from a host on 192.168.10.192／26 network to a host on the LAN attached to router R1?()
A.The path of the packets will be R3 to R2 to R1.B.The path of the packets will be R3 to R1 to R2.C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.D.The path of the packets will be R3 to R1
考题
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally, static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes?（）A.Configure the no ip subnet-zero command on R1, R2, and R3.B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
考题
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
考题
Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）A、Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.B、R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.C、R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.D、All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
考题
Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）A、frame - relay map commands on R3 - R10 referencing the other routers in this groupB、Nine OSPF neighbor commands on each routerC、Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10D、R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRE、R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
考题
Assume two routers on the same subnet， R1 and R2， both configured for HSRP. R1 has a priority of 120.Which of the following HSRP interface configurations will always result in the R2 becoming the primary？（）A、standby 1 priority 110B、standby 1 priority 120C、standby 1 priority 130D、standby 1 priority 110 preemptE、standby 1 priority 120 preemptF、standby 1 priority 130 preempt
考题
R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）A、 LearnB、 SpeakC、 StandbyD、 ListenE、 ActiveF、 Remove
考题
You are the network administrator for TestKing. All network servers run Windows Server 2003. You administer a server named TestKing76. You need to configure TestKing76 to function as a streaming media server for TestKing.com's content team. The content team wants TestKing76 to provide the fastest performance and the most available space possible. Redundancy is not import. TestKing76 currently has three identical, unpartitioned hard disks available. You need to configure the disks to meet the content team's requirements. What should you do?（）A、Create a simple volume on disk and then expand it to the other two disks.B、Create a mirrored volume that uses two of the disks.C、Create a RAID-5 volume that uses all three disks.D、Create a striped volume that uses all three disks.
考题
You need to recommend a Windows Server 2008 R2 server configuration that meets the following requirements： èSupports the installation of Microsoft SQL Server 2008 èProvides redundancy for SQL services if a single server fails What should you recommend？（） A、Install a Server Core installation of Windows Server 2008 R2 Enterprise on two servers. Configure the servers in a failover cluster.B、Install a full installation of Windows Server 2008 R2 Standard on two servers. Configure Network Load Balancing on the two servers.C、Install a full installation of Windows Server 2008 R2 Enterprise on two servers. Configure Network Load Balancing on the two servers.D、Install a full installation of Windows Server 2008 R2 Enterprise on two servers. Configure the servers in a failover cluster.
考题
Your network uses IPv4.You install a server that runs Windows Server 2008 R2 at a branch office. The server is configured with two network interfaces. You need to configure routing on the server at the branch office.Which two actions should you perform？（）A、Install the Routing and Remote Access Services role service.B、Run the netsh ras ip set access ALL command.C、Run the netsh interface ipv4 enable command.D、Enable the IPv4 Router Routing and Remote Access option.
考题
Your company has an IPv4 Ethernet network. A router named R1 connects your segment to the Internet. A router named R2 joins your subnet with a segment named Private1. The Private1 segment has a network address of 10.128.4.0/26. Your computer named WKS1 requires access to servers on the Private1 network.The WKS1 computer configuration is as shown in the following table. Network Addresses IPv4 Address 10.128.64.113 Subnet mask 255.255.252.0 Default Gateway 10.128.64.1 The routers are configured as shown in the following table. Router ID Addresses R1 interface 1 R1 interface 2 (To Internet) 10.128.64.1 131.107.108.37 R2 interface 1 R2 interface 2 10.128.64.10 10.128.4.1 WKS1 is unable to connect to the Private1 network by using the current configuration.You need to add a persistent route for the Private1 network to the routing table on WKS1.Which command should you run on WKS1？（）A、Route add -p 10.128.4.0/22 10.128.4.1B、Route add p 10.128.4.0/26 10.128.64.10C、Route add p 10.128.4.0 mask 255.255.255.192 10.128.64.1D、Route add p 10.128.64.10 mask 255.255.255.192 10.128.4.0
考题
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A
physical layer issuesB
no spanning tree loopsC
use of non-default HSRP timersD
failure to set the command standby 35 preempt
考题
单选题Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A
22B
11C
1D
None
考题
单选题Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）A
Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.B
R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.C
R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.D
All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
考题
单选题You need to recommend a Windows Server 2008 R2 server configuration that meets the following requirements： èSupports the installation of Microsoft SQL Server 2008 èProvides redundancy for SQL services if a single server fails What should you recommend？（）A
Install a Server Core installation of Windows Server 2008 R2 Enterprise on two servers. Configure the servers in a failover cluster.B
Install a full installation of Windows Server 2008 R2 Standard on two servers. Configure Network Load Balancing on the two servers.C
Install a full installation of Windows Server 2008 R2 Enterprise on two servers. Configure Network Load Balancing on the two servers.D
Install a full installation of Windows Server 2008 R2 Enterprise on two servers. Configure the servers in a failover cluster.
考题
单选题You are the network administrator for TestKing. All network servers run Windows Server 2003. You administer a server named TestKing76. You need to configure TestKing76 to function as a streaming media server for TestKing.com's content team. The content team wants TestKing76 to provide the fastest performance and the most available space possible. Redundancy is not import. TestKing76 currently has three identical, unpartitioned hard disks available. You need to configure the disks to meet the content team's requirements. What should you do?（）A
Create a simple volume on disk and then expand it to the other two disks.B
Create a mirrored volume that uses two of the disks.C
Create a RAID-5 volume that uses all three disks.D
Create a striped volume that uses all three disks.
考题
多选题Your network uses IPv4.You install a server that runs Windows Server 2008 R2 at a branch office. The server is configured with two network interfaces. You need to configure routing on the server at the branch office.Which two actions should you perform？（）AInstall the Routing and Remote Access Services role service.BRun the netsh ras ip set access ALL command.CRun the netsh interface ipv4 enable command.DEnable the IPv4 Router Routing and Remote Access option.
考题
多选题Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）Aframe - relay map commands on R3 - R10 referencing the other routers in this groupBNine OSPF neighbor commands on each routerCNine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10DR1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRER3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
考题
单选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）A
The next hop is I2's BGP RIDB
The next hop is I2's IP address used on the R2 - I2 neigh bor relationshipC
The next hop is R2's BGP RIDD
The next hop is R2's IP address used on the R1 - R2 neighbor relationship
考题
多选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers. Which of the following could be used to prevent potential routing loops in this design?（）AUsing an iBGP mesh inside the Enterprise coreBConfiguring default routes in the Enterprise pointing to both R1 and R2CRedistributing BGP routes into the Enterprise IGPDTunneling the packets for the i BGP connection between R1 and R2
考题
单选题Your company has an IPv4 Ethernet network. A router named R1 connects your segment to the Internet. A router named R2 joins your subnet with a segment named Private1. The Private1 segment has a network address of 10.128.4.0/26. Your computer named WKS1 requires access to servers on the Private1 network.The WKS1 computer configuration is as shown in the following table. Network Addresses IPv4 Address 10.128.64.113 Subnet mask 255.255.252.0 Default Gateway 10.128.64.1 The routers are configured as shown in the following table. Router ID Addresses R1 interface 1 R1 interface 2 (To Internet) 10.128.64.1 131.107.108.37 R2 interface 1 R2 interface 2 10.128.64.10 10.128.4.1 WKS1 is unable to connect to the Private1 network by using the current configuration.You need to add a persistent route for the Private1 network to the routing table on WKS1.Which command should you run on WKS1？（）A
Route add -p 10.128.4.0/22 10.128.4.1B
Route add p 10.128.4.0/26 10.128.64.10C
Route add p 10.128.4.0 mask 255.255.255.192 10.128.64.1D
Route add p 10.128.64.10 mask 255.255.255.192 10.128.4.0
考题
多选题R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）ALearnBSpeakCStandbyDListenEActiveFRemove
考题
多选题Assume two routers on the same subnet， R1 and R2， both configured for HSRP. R1 has a priority of 120.Which of the following HSRP interface configurations will always result in the R2 becoming the primary？（）Astandby 1 priority 110Bstandby 1 priority 120Cstandby 1 priority 130Dstandby 1 priority 110 preemptEstandby 1 priority 120 preemptFstandby 1 priority 130 preempt
热门标签
最新试卷