网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
The major source of chemical contaminants in hydraulic fluid is （）.
A
microscopic steel shavings
B
abrasive waste
C
anti-oxidant compounds
D
oxidation by-products
参考答案
参考解析
解析：
暂无解析
更多 “单选题The major source of chemical contaminants in hydraulic fluid is （）.A microscopic steel shavingsB abrasive wasteC anti-oxidant compoundsD oxidation by-products” 相关考题
考题
Overheating of the hydraulic fluid in an electro-hydraulic anchor windlass can result from a/an( ).A.overload on the pump motorB.low fluid level in the reservoirC.low fluid viscosity around the shaft sealD.high oil level in the sump
考题
If you install a new hydraulic hose in a hydraulic system, the hose must be long enough to allow for contraction to preventA.failure of the hydraulic hoseB.excessive flow through the lineC.friction in other areas of the hydraulic systemD.overheating of the hydraulic fluid
考题
Before doing any work on a hydraulic system equipped with accumulators, you shouldA.drain the accumulators and purge with oxygenB.bleed off all stored energy from the accumulators completelyC.charge the accumulators to prevent system energy lossD.pump the hydraulic fluid into the accumulators to prevent fluid loss
考题
Leakage of hydraulic fluid from around the shaft of a hydraulic motor may be caused by ______.A.permanent loss of pump suctionB.worn shaft sealsC.high level in the oil sumpD.low motor RPM
考题
Hydraulic machinery failures are commonly caused by contamination of the hydraulic fluid and ______.A.fluid frictionB.fluid turbulenceC.component misalignmentD.pressure surges
考题
The major cause of trouble in a mechanical-hydraulic governor is contamination of the hydraulic fluid by ______.A.dirtB.fuel oilC.governor cooling waterD.fuel oil tar(焦油)
考题
The storage device for nitrogen-pressurized hydraulic fluid，which is used in closing the blowout preventers is called the ______．A.ActuatorB.AnnulusC.AccumulatorD.Annular preventer
考题
A hydraulic accumulator aboard a ship is designed to ______.A.store fluid under pressureB.act as a fluid reservoirC.provide overpressure reliefD.replenish fluid to a system
考题
单选题What type of valve is used to direct the flow of hydraulic fluid?（）A
Relief valveB
Direction control valveC
Stop valveD
Pressure control valve
考题
单选题In the design of hydraulic piping and equipment consideration is given to minimize turbulence in the hydraulic fluid, as this will cause（）A
molecular fluid vibrationB
energy lossesC
wide pressure variationsD
mechanical damage to control valves
考题
单选题Which of the following statements about pump operations is NOT a correct statement?（）A
In order for a fluid to be pumped, a fluid must be made to flowB
A substance must be cold in order for it to be pumpedC
The kinetic energy imparted by the pump can be used to force a liquid through a hydraulic systemD
A pump must receive its energy from an external source
考题
单选题The major source of chemical contaminants in hydraulic fluid is （）.A
microscopic steel shavingsB
abrasive wasteC
anti-oxidant compoundsD
oxidation by-products
考题
单选题The most common contaminate of governor hydraulic fluid is （）.A
moistureB
dirtC
acidD
air
考题
单选题One function provided by a hydraulic accumulator is to（）A
provide an area where air can separate from the oilB
provide an area to separate solid contaminants from the oilC
act as an oil and water separatorD
absorb shocks occurring in the system
考题
单选题A hydraulic accumulator aboard a ship is designed to（）.A
store fluid under pressureB
act as a fluid reservoirC
provide overpressure reliefD
replenish fluid to a system
考题
单选题If you are given the job of adding hydraulic fluid to a mooring winch, and are not certain as to the type of fluid to use, you should （）.A
add fluid that is the same color as the fluid in the reservoirB
add turbine oil because it is always a good substituteC
add any oil that has the same viscosity as the hydraulic fluidD
check the winch manufacturers instruction book
考题
单选题Before doing any work on a hydraulic system equipped with accumulators, you should（）A
drain the accumulators and purge with oxygenB
bleed off all stored energy from the accumulators completelyC
charge the accumulators to prevent system energy lossD
pump the hydraulic fluid into the accumulators to prevent fluid loss
考题
单选题An orifice-check valve placed in a hydraulic system is used to（）A
regulate the fluid flow in either directionB
restrict movement of hydraulic fluid in one direction, but allow free movement in the other directionC
allow free movement of hydraulic fluid in both directionsD
allow a restricted fluid flow in one direction only
考题
单选题The major cause of trouble in a mechanical-hydraulic governor is contamination of the hydraulic fluid by （）A
dirtB
fuel oilC
governor cooling waterD
fuel oil tars
考题
单选题If a radial piston hydraulic pump fails to deliver rated fluid volume, the cause can be （）.A
contaminated fluidB
pitted thrust ringsC
worn pintle bearingsD
obstructed suctions passage
考题
单选题Leakage of hydraulic fluid from around the shaft of a hydraulic motor may be caused by（）A
permanent loss of pump suctionB
worn shaft sealsC
high level in the oil sumpD
low motor RPM
考题
单选题How can the chance of contaminating hydraulic fluid be decreased when working on hydraulic system?（）A
clean the fittings before they are disconnectedB
Place drip pans under leaky fittingsC
Seal any cracks in lines with PermatexD
Coat all threads with graphite oil
考题
单选题Compensated flow control or constant flow valves are used in hydraulic systems to（）A
compensate for major leaks in the systemB
maintain the original fluid viscosityC
allow for changes in pressure and temperature within the systemD
assure constant fluid temperature
考题
单选题A hydraulic accumulator is designed to（）.A
store fluid under pressureB
act as a fluid reservoirC
provide overpressure reliefD
replenish fluid to a system
考题
单选题Hydraulic machinery failures are commonly caused by contamination of the hydraulic fluid and （）.A
fluid frictionB
fluid turbulenceC
component misalignmentD
pressure surges
考题
单选题In a shell-and-tube type hydraulic fluid cooler, the amount of heat transferred from the hydraulic fluid to the cooling water depends upon（）A
the temperature of the hydraulic fluidB
the flow rate of the hydraulic fluidC
the temperature of the cooling waterD
all of the above
考题
单选题Hydraulic machinery failures are commonly caused by misalignment of the system components and by （）.A
hydraulic fluid contaminationB
excessive fluid frictionC
turbulent fluid flowD
fluid pressure surges
热门标签
最新试卷