网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
The （） of the main shaft should be measured with a （）.
A
clearance；calipers
B
sinking；bridge gauge
C
diameter；bridge gauge
D
clearance；lead wire
参考答案
参考解析
解析：
暂无解析
更多 “单选题The （） of the main shaft should be measured with a （）.A clearance；calipersB sinking；bridge gaugeC diameter；bridge gaugeD clearance；lead wire” 相关考题
考题
During the dock repair,______should be measured firstly before tail shaft drawn out.A.the sinking of tail shaftB.the clearance of stern bearingC.the total flexure of shaftD.main engine crankshaft deflection
考题
Which of the following is operated from the main engine room console on an automated vessel?A.Fire pump and lube oil pumpB.Lube oil pump and distilling plantC.Distilling plant and shaft alley doorD.Shaft alley door and fixed CO2 release
考题
When the tail-shaft is drawn from a vessel in dry-dock, which of the following inspections is required to be carried out?A.The propeller hub taper and shaft keyway should be inspected for cracks or corrosionB.The stern bearing alignment with the stern frame should be checkedC.The interior of the stern tube should be inspected for leaksD.The shaft liner should be removed and inspected for cracks
考题
When navigating in high latitudes and using a chart based on a Lambert conformal projection，______.A.a straight line drawn on the chart approximates a great circleB.the chart should not be used outside of the standard parallelsC.the course angle is measured at the mid-longitude of the track lineD.distance cannot be measured directly from the chart
考题
单选题On a large low-speed main propulsion diesel engine, lower main bearing wear is usually measured by using a/an （）A
dial indicatorB
outside caliperC
bridge gaugeD
tram rod
考题
单选题On a single-screw vessel the stern frame（）.A
furnishes support to the rudder，propeller shaft，and transom frameB
provides foundations for after mooring winchesC
provides foundations for the main propulsion enginesD
transfers the driving force of the propeller to the hull
考题
单选题During the dock repair, should be measured firstly before tail shaft drawn out（）A
the sinking of tail shaftB
the clearance of stern bearingC
the total flexure of shaftD
main engine crankshaft deflection
考题
单选题The quality of teaching should be measured by the degree ______ which the students’ potentiality is developed.A
toB
ofC
with D
in
考题
单选题When the tail-shaft is drawn from a vessel in dry-dock, which of the following inspections is required to be carried out?（）A
The propeller hub taper and shaft keyway should be inspected for cracks or corrosionB
The stern bearing alignment with the stern frame should be checkedC
The interior of the stern tube should be inspected for leaksD
The shaft liner should be removed and inspected
考题
单选题The main function of tie rods in the construction of large, low speed diesel engines is to（）.A
stiffen the bedplate in way of the main bearings to increase the engines longitudinal strengthB
accept most of the tensile loading that results from the firing forces developed during operationC
mount the engine frame securely to the hull to prevent shaft coupling misalignmentD
connect the crosshead solidly to the piston rod
考题
单选题Why a gearbox is needed in a ship driven by a medium-speed diesel engine?（）A
To reduce the main engine speedB
To increase the main engine speedC
To govern the main engine speedD
To fix the propeller shaft
考题
单选题Signs of racking stresses generally appear at the（）.A
bow and stern shell frames and platingB
junction of the frames with the beams and floorsC
garboard strake，at each side of the keelD
thrust bearing of the main shaft
考题
单选题One of the main functions of wearing rings, as used in a centrifugal pump, is to （）.A
maintain radial alignment between the pump impeller and casingB
absorb all impeller shaft end thrustC
prevent water leakage to the atmosphereD
prevent wear of the pump casing and/or impeller
考题
单选题A vessel has been equipped with an oil lubricated stern bearing and is undergoing a routine dry-dock.Which of the following inspection should be made when the tail-shaft has been drawn?（）A
The overall condition of the bearing surface should be examinedB
The shaft liner should be inspected for cracks and tested to insure a tight fitC
The stern tube should be tested for cracks with dye penetrantD
all of above
考题
单选题The load limitation of governor should be reduced when ship navigating at sea, the main reason is to（）A
prevent the diesel engine surgingB
prevent governor from being damaged because of swingC
reduce the probability of the crank shaft being torsional vibrated and resonatedD
prevent the main engine being overload or overspeed
考题
单选题When ship in the dock repairing, engine department should emphasize on the inspection of（）A
sea valve chest, sect valve, thrusterB
bilge motherboard, steering and the shaft systemC
sea water systemD
fresh water system
考题
单选题The diameters of the crankpins should be measured using （）.A
a micrometerB
a bridge gaugeC
a spannerD
a wrench
考题
单选题Some vessels are equipped with a water lubricated stern robeWhen at sea, operating under normal conditions, the water service valve from the ships saltwater system to the bearing should be （）.A
closed, and no leakage permitted across the shaft packingB
closed, and only slight leakage permitted across the shaft packingC
open, and no leakage permitted across the shaft packingD
open, and only slight leakage permitted across the shaft packing
考题
单选题When the vessel shafting are installed, the slightly inclined of the shaft line should be rectified by（）A
adjusting the position of the intermediate bearingB
changing the position of the main engine installationC
adjusting the center line of the propellerD
changing the position of the thrust block
考题
单选题The shaft and spare parts（） should be well greased in order to avoid corrosion.A
in the store roomB
in the cylinderC
in the scavenge air boxD
in the water box
考题
单选题During the dock repair, when installing the tail shaft and propeller, who should be on the spot to supervise?（）A
chief engineerB
the engineerC
captainD
any member of the engine department
考题
单选题During the deck repair,（） should be measured firstly before tail shaft is drawn out.A
the sinking of tail shaftB
the clearance of stern bearingC
the total flexure of both end bearingD
main engine crankshaft deflection
考题
单选题The diameter of the crank-pins should be measured with a （）.A
salinometerB
thermometerC
tachometerD
micrometer
热门标签
最新试卷