网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
S2126G交换机如何将接口设置为TAGVLAN模式？（）
- A、switchport mode tag
- B、switchport mode trunk
- C、trunk on
- D、set port trunk on
参考答案
更多 “S2126G交换机如何将接口设置为TAGVLAN模式？（）A、switchport mode tagB、switchport mode trunkC、trunk onD、set port trunk on” 相关考题
考题
如下图所示，3com和Cisco公司的交换机相互连接，在两台交换机之间需传输ULANID为1、10、20和30的4个VLAN信息，Catalyst 3548交换机VLAN Trunk的正确配置是A．Switch-3548 (config-if) #switchport trunk encapsulation dot 1 q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30B．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation isl Switch-3548 (config-if) #switchport trunk allowed vlan 1-30C．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation negotiate Switch-3548 (config-if) #switchport trunk allowed vlan 1-30D．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation dot 1q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30
考题
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)A. Switch(vlan) mode trunkB. Switch(config) switchport access mode trunkC. Switch(config-if) switchport mode trunkD. Switch(config-if) switchport trunk encapsulation dot1qE. Switch(config) switchport access mode 1F. Switch(vlan) trunk encapsulation dot1q
考题
以下哪个命令用于创建一个trunk?A、switchport mode trunkB、switchport trunk enableC、switchport trunkD、trunk enableA．B．C．D．
考题
在Cisco Catalyst 2950交换机上配置Trunk接口模式时,如果要禁止接口产生DTP帧,应该通过以下( )命令实现。
A、switchport mode accessB、switchport mode dynamic desirableC、switchport mode autoD、switchport nonegotiate
考题
现需要将两台Cisco Catalyst 2950交换机之间的链路配置为中继链路(Trunk),若一端的端口已使用“Switchport mode trunk”命令设置过,则另一端的端口使用( )命令能保证链路成为中继链路。
A、Switchport mode accessB、Switchport mode trunkC、Switchport mode dynamic autoD、Switchport mode dynamic desirable
考题
Which commands, when used together, would create an 802.1Q link?()
A. Switch(vlan)# mode trunkB. Switch(config)# switchport access mode trunkC. Switch(config-if)# switchport mode trunkD. Switch(config-if)# switchport trunk encapsulation dot1qE. Switch(config)# switchport access mode 1F. Switch(vlan)# trunk encapsulation dot1q
考题
Which set of commands is recommended to prevent the use of a hub in the access layer?()
A.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1B.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1C.switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1D.switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
考题
S2126G交换机如何将接口设置为TAGVLAN模式?()
A.switchport mode tagB.switchport mode trunkC.trunk onD.set port trunk on
考题
S2126交换机如何将接口设置为TAGVLAN模式?()
A.trunk onB.set port trunk onC.switchport mode tagD.switchport mode trunk
考题
Which commands, when used together, would create an 802.1Q link?（）A、Switch(vlan)# mode trunkB、Switch(config)# switchport access mode trunkC、Switch(config-if)# switchport mode trunkD、Switch(config-if)# switchport trunk encapsulation dot1qE、Switch(config)# switchport access mode 1F、Switch(vlan)# trunk encapsulation dot1q
考题
Which configuration option will cause the link between two Cisco 3600 Series Multiservice Platforms to become a functional trunk？（）A、switchport dynamic auto switchport dynamic autoB、switchport access vlan 10 switchport mode dynamic desireableC、switchport mode trunk switchport nonegotiateD、Leave both ports with the default trunk settings
考题
能够在CiscoIOS软件中正确地将端口配置为ISL封装的命令是（）。A、Switch(config-if)#switchport mode trunk islB、Switch(config-if)#switchport mode encapsulation islC、Switch(config-if)#switchport trunk encapsulation islD、Switch(config-if)#switchport mode trunk encapsulation isl
考题
配置CISCO7600以太端口为Trunk模式的命令是（）A、config runkB、mode trunkC、switchport mode trunkD、switchport mode access
考题
S2126交换机如何将接口设置为TAGVLAN模式？（）A、trunk onB、set port trunk onC、switchport mode tagD、switchport mode trunk
考题
Which set of commands is recommended to prevent the use of a hub in the access layer?（）A、switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1B、switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1C、switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1D、switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
考题
You are configuring a Cisco multilayer switch for the Company network. Which command would you use to configure a port to act as a routed interface？（）A、 ip routingB、 switchport mode trunkC、 no switchportD、 switchport trunk native vlan 1E、 None of the other alternatives apply
考题
交换机如何将接口设置为TAG VLAN模式？（）A、switchport mode tagB、switchport mode trunkC、trunk onD、set port trunk on
考题
You are configuring an 802.1Q trunk between a Layer 2 switch and a firewall. You read in the documentation that the best way to set up a trunk is to set the port as dynamic desirable. The trunk is not coming up. Which one of these options would be a valid explanation？ （）A、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode ONB、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode to OFFC、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode asauto.D、The firewall does not support DTP. You should set the switchport trunk mode to ON
考题
A Cisco switch has this configuration for a port channel connecting to an ESXi using dual NICs and is intended for use with an N1Kv. Interface fastethernet 1/10 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface fastethernet 1/11 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface port-channel 10 Switchport mode trunk Switchport allowed vlan all No shut Which Port Channel configuration must be used on the Nexus 1000v port-profile？（）A、 MAC pinningB、 Cisco Discovery Protocol pinningC、 Mode OnD、 Mode ActiveE、 No port channel configuration
考题
Which command alone will disable trunking on a Layer 2 switch port？（）A、no switchport trunk native vlan vlan-idB、switchport nonegotiateC、no switchport mode dynamic desirableD、switchport mode access
考题
单选题交换机如何将接口设置为TAG VLAN模式？（）A
switchport mode tagB
switchport mode trunkC
trunk onD
set port trunk on
考题
单选题如下图所示，3com和Cisco公司的交换机相互连接，在两台交换机之间需传输VLAN ID为1、10、20和30的5个VLAN信息，Catalyst3548交换机VLAN Trunk的正确配置是（ ）。A
Switch-3548（config-if）#switchport trunk encapsulation dotlqSwitch-3548（config-if）#switchport trunk allowed vlan 1，10，20，30B
Switch-3548（config-if）#switchport mode trunkSwitch-3548（config-if）#switchport trunk encapsulation islSwitch-3548（config-if）#switchport tnmk allowed vlan 1-30C
Switch-3548（config-if）#switchport mode trunkSwitch-3548（config-if）#switchport trunk encapsulation negotiateSwitch-3548（config-if）#switchport trunk allowed vlan 1-30D
Switch-3548（config-if）#switchport mode trunkSwitch-3548（config-if）#switchport trunk encapsulation dotlqSwitch-3548（config-if）#switchport trunk allowed vlan 1，10，20，30
考题
单选题S2126交换机如何将接口设置为TAGVLAN模式？（）A
trunk onB
set port trunk onC
switchport mode tagD
switchport mode trunk
考题
单选题Which command alone will disable trunking on a Layer 2 switch port？（）A
no switchport trunk native vlan vlan-idB
switchport nonegotiateC
no switchport mode dynamic desirableD
switchport mode access
考题
单选题You are configuring a Cisco multilayer switch for the Company network. Which command would you use to configure a port to act as a routed interface？（）A
ip routingB
switchport mode trunkC
no switchportD
switchport trunk native vlan 1E
None of the other alternatives apply
考题
单选题S2126G交换机如何将接口设置为TAGVLAN模式？（）A
switchport mode tagB
switchport mode trunkC
trunk onD
set port trunk on
热门标签
最新试卷