网友您好, 请在下方输入框内输入要搜索的题目:
题目内容
(请给出正确答案)
单选题
The ()pump is usually used as the bilge feed pump to an oily water separator.
A
turbine
B
screw
C
vane
D
ejector
参考答案
参考解析
解析:
暂无解析
更多 “单选题The ()pump is usually used as the bilge feed pump to an oily water separator.A turbineB screwC vaneD ejector” 相关考题
考题
Which of the following terms is used to identify the pressure of the liquid entering a pump?A.Suction headB.Pump headC.Discharge headD.Total head
考题
If the feed pump for an auxiliary boiler fails to deliver the feed water to the boiler, the cause may be ______.A.high steam pressure in the boilerB.abnormally high feed-water temperatureC.abnormally high boiler water temperatureD.steam demand exceeding feed pump capacity
考题
Which method should be used to warm up the pump turbines prior to discharge ________.A.Lock the turbine rotor and slowly bleed in steam until operating temperature is reachedB.Run the pump at high speed with the discharge valves closedC.Run the turbine at slow speed with the pump disconnectedD.Shut the discharge valve and run the pump at slow speed
考题
单选题The bilge pump on a fishing vessel().A
must be fixed if the vessel exceeds 12 meters in lengthB
may be used as a fire pumpC
must be portable if there are more than 4 watertight compartmentsD
must be capable of pumping at least 450 gpm
考题
单选题Which of the following pumps is most suitable for an oily water separator?()A
reciprocating pumpB
vane pumpC
mono pumpD
axial-flow pump
考题
单选题The bilge system has been performing well; however, the aft starboard engine room bilgewell suddenly fails to be pumped outWhich of the following should be done first to determine the cause?()A
Open the bilge pump for inspectionB
Remove each of the manifold valvesC
Remove only the manifold valve to the affected bilge-wellD
Attempt to pump out another bilge well to determine if the entire system is affected
考题
单选题A centrifugal bilge pump requires priming ().A
primarily to lubricate the shaft sealsB
due to the inability of this type of pump to lift water to cover the suction (eye) of the impellerC
to initially unload the pump by having its head pressure equal to discharge pressureD
in order to overcome the potential energy of water in the discharge line
考题
单选题The boiler feed water check valves are located on the ()A
feed pump suction lineB
hot wellC
shell of the feed heaterD
feed lines to the boiler
考题
单选题Which method should be used to warm up the pump turbines prior to discharge().A
Lock the turbine rotor and slowly bleed in steam until operating temperature is reachedB
Run the pump at high speed with the discharge valves closedC
Run the turbine at slow speed with the pump disconnectedD
Shut the discharge valve and run the pump at slow speed
考题
单选题Before operating a non-oceangoing ship greater than 100 gross tons it must have a fixed piping system to discharge oily mixtures ashore. This system must include().A
approved oily-water separating equipmentB
a fixed or portable containment system at the shore connectionC
a spare pump in case the main pump is inoperativeD
at least one outlet accessible from the weather deck
考题
单选题One of the main functions of wearing rings, as used in a centrifugal pump, is to ().A
maintain radial alignment between the pump impeller and casingB
absorb all impeller shaft end thrustC
prevent water leakage to the atmosphereD
prevent wear of the pump casing and/or impeller
考题
单选题Cooling water pumps driven by direct reversing diesel engines are usually of the straight impeller vane type pump with a concentric housing to()A
facilitate bi-directional operationB
provide the greatest pump efficiencyC
prevent pump clogging from marine growthD
prevent cavitation at the pump outlet
考题
单选题The pressure difference of the gauge on the oily water separator increases greatly, the reason is()A
the filter is cloggedB
bilge suction value is cloggedC
suction value and discharge value of the pump do not open fullyD
screw pump is worn seriously and volumetric efficiency is decreased
考题
单选题The purpose of the wearing rings used in a centrifugal pump is to ().A
prevent an internal explosion in the pump when it is overheatedB
enable a visual inspection of the pump while it is runningC
insure a proper alignment of the pump coupling to the driverD
accommodate for friction between the impeller and the easing
考题
单选题The most suitable pump for oily water separator feed duties is ().A
a reciprocating pumpB
a vane pumpC
a centrifugal pumpD
a triple screw pump
考题
单选题The pump used to send the bilge water into the oily water separator()the mixture because this might create finer oil particles.A
should agitateB
should not agitateC
should mix upD
should not add up
考题
单选题According to the SOLAS convention, the bilge water system ()A
must connect the bilge well suction directlyB
should not pump out the water accumulated in the cargosC
should not used for emergency drainage in case of ship collisionD
should connect to the fire fighting system directly
考题
单选题If it becomes necessary to cutout an individual cylinder of a large, low-speed, main propulsion diesel engine, the fuel to that cylinder should be secured and its ()A
fuel pump should be removed and all connections blanked offB
cylinder oil feed rate should be increased slightly above that used at normal sea speedC
cylinder oil feed rate should be reducedD
cylinder oil feed rate should be increased to the maximum flow capable of the metering pump
考题
单选题The boiler feed pump discharge pressure is higher than the steam drum pressure to ().A
ensure feed water flow into the boilerB
keep the steam drum pressure highC
prevent water hammer in the feed lineD
help the feed water flash to steam
考题
单选题The lube oil pump used in a diesel engine is a ().A
volute pumpB
centrifugal pumpC
diaphragm pumpD
gear pump
考题
单选题If a bilge pump is able to develop vacuum, but is unable to sufficiently pump out the bilges, you would check for all of the following EXCEPT ().A
the circuit breakerB
for leaks in the suction pipingC
relief valve is not properly seatedD
the suction strainer
考题
单选题Oil water separators are used to ensure that ships don’t discharge oil when () bilge water.A
to pump offB
being pumpedC
pumping outD
it pumping out
考题
单选题On modern ships, centrifugal pump with a self-primer has replaced reciprocating pump as bilge pump because()A
centrifugal pump is cheaper than reciprocating pumpB
the size of centrifugal pump with same capacity is smaller than that of reciprocating pumpC
centrifugal pump makes maintenance easier than reciprocating pump doesD
all of the above
考题
单选题If the feed pump for an auxiliary boiler fails to deliver the feed water to the boiler, the cause maybe ().A
high steam pressure in the boilerB
abnormally high feed water temperatureC
abnormally high boiler water temperatureD
steam demand exceeding feed pump capacity
考题
单选题The ()pump is usually used as the lubricating oil pump.A
turbineB
screwC
vaneejectorD
centrifugal
热门标签
最新试卷