网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Which switch would STP choose to become the root bridge in the selection process?（）
- A、32768: 11-22-33-44-55-66
- B、32768: 22-33-44-55-66-77
- C、32769: 11-22-33-44-55-65
- D、32769: 22-33-44-55-66-78
参考答案
更多 “Which switch would STP choose to become the root bridge in the selection process?（）A、32768: 11-22-33-44-55-66B、32768: 22-33-44-55-66-77C、32769: 11-22-33-44-55-65D、32769: 22-33-44-55-66-78” 相关考题
考题
A new switch is installed in the Ezonexam network. This switch is to be configured so that VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.Which of the conditions below have to be met in order for this to occur? (Choose all that apply).A. The switch that will share the VLAN information must be in the VTP Server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be configured to use the same VTP version.E. The switches must be configured to use the same STP version.F. The switches must be configured to use the same type of ID tagging.G. The switches must be connected over VLAN trunks.
考题
Why would the Ezonexam administrator change the value of the spanning-tree priority of a switch?A. in order to optimize the path that frames take from source to destinationB. to increase the priority so a designated port will become a root portC. to increase the BID, so the switch is more likely to become root bridgeD. in order to allow VLANs to be sent from one switch to another across a single linkE. to force a given switch to become an STP serverF. None of the above
考题
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? (Choose two)A. The switch must be reachable through a port connected to its management VLAN.B. The switch console port must be connected to the Ethernet LAN.C. The switch must be fully configured as an SNMP agent.D. The switch must be configured with an IP address, subnet mask, and default gateway.E. The switch management VLAN must be created and have a membership of at least one switch port.F. The switch must be connected to a router over a VLAN trunk.
考题
A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?()
A.StraightB.ConsoleC.CrossoverD.Loopback
考题
Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?()
A.As FastEthernet0/12 will be the last to come up, it will not be blocked by STP.B.Remote access management of this switch will not be possible without configuration change.C.More VLANs will need to be created for this switch.D.The switch will need a different IOS code in order to support VLANs and STP.
考题
Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? ()
A.Switch A - Fa0/0B.Switch A - Fa0/1C.Switch B - Fa0/0D.Switch B - Fa0/1E.Switch C - Fa0/0F.Switch C - Fa0/1
考题
Which switch would STP choose to become the root bridge in the selection process?()
A.32768: 11-22-33-44-55-66B.32768: 22-33-44-55-66-77C.32769: 11-22-33-44-55-65D.32769: 22-33-44-55-66-78
考题
Which are valid modes for a switch port used as a VLAN trunk (Choose three.)()。
A.transparentB.autoC.onD.desirableE.blockingF.forwarding
考题
A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?（）A、StraightB、ConsoleC、CrossoverD、Loopback
考题
Which spanning Tree Protocol has been implemented on switch 2？ （）A、STP/IEEE 802.1DB、MSTP/IEEE 802.1sC、PVST+D、PVRSTE、None of the other alternatives apply
考题
A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）A、The switch port link lights will be off on both switches indicating the ports are not connected.B、The switch port link light will be off on one switch indicating that STP has disabled the port.C、The switch port link lights will flash amber indicating an error.D、The switch port link lights will be green indicating normal operation.
考题
Which two of the following statements describe a routed switch port on a multilayer switch？（）A、Layer 2 switching and Layer 3 routing are mutually supported.B、The port will not be associated with any VLAN.C、The routed switch port supports VLAN subinterfaces.D、The routed switch port is used when a switch has only one port per VLAN or subnet.E、The routed switch port ensures that STP remains in the forwarding state.
考题
Which are valid modes for a switch port used as a VLAN trunk (Choose three.)（）。A、transparentB、autoC、onD、desirableE、blockingF、forwarding
考题
Why would an administrator change the value of the spanning-tree priority of a switch?（）A、in order to optimize the path that frames take from source to destinationB、to increase the priority so a designated port will become a root portC、to increase the BID, so the switch is more likely to become root bridgeD、in order to allow VLANs to be sent from one switch to another across a single linkE、to force a given switch to become an STP server
考题
Which three statements about STP timers are true？（）A、STP timers values （hello， forward delay， max age） are included in each BPDU.B、A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.C、To successfully exchange BPDUs between two switches， their STP timers value （hello， forward delay， max age） must be the same.D、If any STP timer value （hello， forward delay， max age） needs to be changed， it should at least be changed on the root bridge and backup root bridge.E、On a switched network with a small network diameter， the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.F、The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.
考题
Which protocol provides a method of sharing VLAN configuration information between two Cisco switch？（）A、VTPB、802.1QC、RSTPD、STP
考题
If an enterprise customer required a switch for their branch office access layer, which family of switches would the customer likely choose from?（）A、Cisco Catalyst 2000 and 3000B、Cisco NexusC、Cisco Catalyst 4000 and 6000D、Cisco SFS 3000/7000
考题
When the Catalyst switch R1 is enabled to use VTP， which information does it advertise on its trunk ports？（）A、 VTP modeB、 STP root statusC、 Negotiation statusD、 Management domainE、 Configuration revision number
考题
Which of the following protocols would a multilayer switch use to learn the IP address of a directly connected device？（）A、ARPB、BOOTPC、Inverse-ARPD、DNS
考题
单选题A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）A
The switch port link lights will be off on both switches indicating the ports are not connected.B
The switch port link light will be off on one switch indicating that STP has disabled the port.C
The switch port link lights will flash amber indicating an error.D
The switch port link lights will be green indicating normal operation.
考题
单选题Refer to the exhibit. Which of these statements correctly describes the state of the switch once the boot process has been completed?（）A
As FastEthernet0/12 will be the last to come up, it will not be blocked by STP.B
Remote access management of this switch will not be possible without configuration change.C
More VLANs will need to be created for this switch.D
The switch will need a different IOS code in order to support VLANs and STP.
考题
多选题Which three connection options are available when configuring a switch port to be part of a privateVLAN? （）(Choose three.)Aisolated modeBswitchport modeCmodular modeDcommunity modeEpromiscuous modeFglobal mode
考题
单选题Why would an administrator change the value of the spanning-tree priority of a switch?（）A
in order to optimize the path that frames take from source to destinationB
to increase the priority so a designated port will become a root portC
to increase the BID, so the switch is more likely to become root bridgeD
in order to allow VLANs to be sent from one switch to another across a single linkE
to force a given switch to become an STP server
考题
单选题If an enterprise customer required A switch for their branch office access layer, which family of switches would the customer likely choose from?（）A
Cisco SFS 3000/7000B
Cisco Catalyst 2000 and 3000C
Cisco Catalyst 4000 and 6000D
Cisco Nexus
考题
单选题Which switch would STP choose to become the root bridge in the selection process?（）A
32768: 11-22-33-44-55-66B
32768: 22-33-44-55-66-77C
32769: 11-22-33-44-55-65D
32769: 22-33-44-55-66-78
考题
单选题Which of the following options would you choose to implement controlled access using remote authentication for your networks？（）A
OiDB
RADIUSC
Wallet ManagerD
Oracle Names Server
考题
多选题Which are valid modes for a switch port used as a VLAN trunk? (Choose three.)（）AtransparentBautoConDdesirableEblockingFforwarding
热门标签
最新试卷