考题
A Ezonexam switch is configured with all ports assigned to VLAN 2. In addition, all ports are configured as full-duplex FastEthernet. What is the effect of adding switch ports to a new VLAN on this switch?A.The additions will create more collisions domains.B.IP address utilization will be more efficient.C.More bandwidth will be required than was needed previously.D.An additional broadcast domain will be created.E.The possibility that switching loops will occur will increase dramatically.
考题
A new switch is being installed in the Ezonexam network and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this? (Choose all that apply).A.You must set each end of the trunk line to IEEE 802.1e encapsulation.B.You must set the same VTP management domain name on both switches.C.You must set all ports on the two switches as access ports.D.You must configure one of the switches as a VTP server.E.You must use a rollover cable to connect the two switches.
考题
You need to create a new VLAN on your Catalyst switch. This VLAN is to be named EZONEXAM. Which of the following need to be completed for the creation of this new VLAN? (Select all that apply)A. The EZONEXAM VLAN must be created.B. The desired ports must be added to the new EZONEXAM VLAN.C. The EZONEXAM VLAN must be added to all of the domains.D. The EZONEXAM VLAN must be named.E. An IP address must be configured for the EZONEXAM VLAN.F. None of the above. VLAN creations are automatic.
考题
The Ezonexam network administrator needs to a switch named VE1 to become the root bridge for a redundant path switched network. What can be done to ensure that VE1 will always assume the role as the root bridge?A.Assign the switch a higher MAC address than the other switches in the network haveB.Establish a direct link from the switch to all other switches in the networkC.Configure the switch full-duplex operation and configure the other switches for half-duplex operationD.Configure the switch so that it has lower priority than other switches in the networkE.None of the above
考题
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()A. The switch name must match the workgroup name of the local network.B. The switch must be configured with an IP address and default gateway.C. The remote workstations must have access to the management VLAN of the switch.D. CDP must be enabled on the switch so that it can be located by other devices on the network.
考题
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.Which of the conditions below have to be met in order for this to occur?()A. The switch that will share the VLAN information must be in the VTP Server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be configured to use the same VTP version.E. The switches must be configured to use the same STP version.F. The switches must be configured to use the same type of ID tagging.G. The switches must be connected over VLAN trunks.
考题
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network.What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?()A. The switch that will share its VLAN configuration must be in VTP server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be connected over VLAN trunks.E. The switches must be configured to use the same STP version.F. The switches must have VTP pruning activated.
考题
A new switch is being installed and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches.Which of the following must you do to accomplish this?()A. You must set each end of the trunk line to IEEE 802.1e encapsulation.B. You must set the same VTP management domain name on both switches.C. You must set all ports on the two switches as access ports.D. You must configure one of the switches as a VTP server.E. You must use a rollover cable to connect the two switches.
考题
A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration?()
A. A switch in the VTP client mode cannot update its local VLAN database.B. A trunk link must be configured between the switches to forward VTP updates.C. A switch in the VTP server mode can update a switch in the VTP transparent mode.D. A switch in the VTP transparent mode will forward updates that it receives to other switches.E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.
考题
Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?()A.The access link needs to be configured in multiple VLANs.B.The link between the switches is configured in the wrong VLAN.C.The link between the switches needs to be configured as a trunk.D.VTP is not configured to carry VLAN information between the switches.E.Switch IP addresses must be configured in order for traffic to be forwarded between the switches
考题
Given the output of the Floor3 switch, what statement describes the operation of this switch()。
A.VTP is disabled on this switch.B.The switch can create, change, and delete VLANs.C.The switch learns VLAN information but does not save it to NVRAM.D.The switch can create VLANs locally but will not forward this information to other switches.E.The switch learns VLAN information and updates the local VLAN data base in NVRAM.
考题
A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge()。A.Establish a direct link from the switch to all other switches in the network.B.Assign the switch a higher MAC address than the other switches in the network have.C.Configure the switch so that it has a lower priority than other switches in the network.D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.E.Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
考题
Which MST configuration statement is correct? ()A、 MST configurations can be propagated to other switches using VTP.B、 After MST is configured on a Switch, PVST+ operations will also be enabled by default.C、 MST configurations must be manually configured on each switch within the MST region.D、 MST configurations only need to be manually configured on the Root Bridge.E、 MST configurations are entered using the VLAN Database mode on Cisco Catalyst switches.
考题
A switch that is to be added to the production network has been preconfigured (trunks, VLANs, VTP, and STP) and was tested in your lab. After installing the switch into the network, the entire network went down. What might explain what happened? ()A、The new switch happened to be running Cisco Catalyst operating system, while the other network switches were running Cisco IOS Software.B、The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.C、The link costs on the new switch are set to a high value, causing all ports on the new switch to go into a forwarding mode and none into blocking mode, thereby causing a spanning-tree loop.D、The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
考题
You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan? ()A、Verify that different native VLANs exist between two switches for security purposes.B、Verify that the VLAN was added on all switches with the use of the show vlan command. C、Verify that the switch is configured to allow for trunking on the switch ports.D、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.
考题
You need to connect two Company core switches via an ISL trunk. Which statement is true regarding the configuration of ISL trunks? ()A、 A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.B、 All Catalyst switches support ISL trunking.C、 A Catalyst switch will report giants if one side is configured for ISL while the other side is not.D、 ISL trunking requires that native VLANs match.E、 None of the other alternatives apply
考题
You want to configure switch R1 to propagate VLAN information across the Company network using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()A、VTP modeB、VTP passwordC、VTP revision numberD、VTP pruningE、VTP domain nameF、None of the other alternatives apply
考题
Given the output of the Floor3 switch, what statement describes the operation of this switch()。A、VTP is disabled on this switch.B、The switch can create, change, and delete VLANs.C、The switch learns VLAN information but does not save it to NVRAM.D、The switch can create VLANs locally but will not forward this information to other switches.E、The switch learns VLAN information and updates the local VLAN data base in NVRAM.
考题
You have just created a new VLAN on your network. What is one step that you should include in your VLAN-based implementation and verification plan? ()A、Verify that trunked links are configured to allow the VLAN traffic.B、Verify that the switch is configured to allow for trunking on the switch ports.C、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.D、Verify that different native VLANs exist between two switches for security purposes.
考题
Before inserting a new switch in the network,the network administrator checks that the VTP domain name is correct,the VTP mode is set to server, and revision is lower than the switches in the network. The administrator then configures interfaces and trunks,erases existing VLANs,and connects the switch to the network. Following that procedure,there is no connectivity in the network. What is a possible cause of this problem?()A、Because the configuration revision of the new switches is lower than the rest of the network, it can change the VLAN database of the other switches.B、As a VTP server, the new switch deleted all VLANs of the network.C、Erasing VLANs increases the VTP configuration revision.D、Since the configuration revision of the network is higher than the new switch, the VLAN database was automatically synchronized.
考题
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
考题
Switch A is configured with VLAN 105 and 106. Switch Bis configured with VLAN 105 and 107.Both switches are connected with a fiber cable. In order for packets from all VLANs to cross thefiber cable, which of the following configurations MUST be present? ()A、Reverse ARPB、Full duplex on the fiber linkC、PoED、802.1q trunking
考题
多选题By default, each port in a Cisco Catalyst switch is assigned to VLAN1. Which two recommendations are key to avoid unauthorized management access? ()ACreate an additional ACL to block the access to VLAN 1.BMove the management VLAN to something other than default.CMove all ports to another VLAN and deactivate the default VLAN.DLimit the access in the switch using port security configuration.EUse static VLAN in trunks and access ports to restrict connections.FShutdown all unused ports in the Catalyst switch.
考题
单选题A switch that is to be added to the production network has been preconfigured (trunks, VLANs, VTP, and STP) and was tested in your lab. After installing the switch into the network, the entire network went down. What might explain what happened? ()A
The new switch happened to be running Cisco Catalyst operating system, while the other network switches were running Cisco IOS Software.B
The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.C
The link costs on the new switch are set to a high value, causing all ports on the new switch to go into a forwarding mode and none into blocking mode, thereby causing a spanning-tree loop.D
The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
考题
单选题You want to configure switch R1 to propagate VLAN information across the Company network using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()A
VTP modeB
VTP passwordC
VTP revision numberD
VTP pruningE
VTP domain nameF
None of the other alternatives apply
考题
多选题An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?()AThe switch that will share its VLAN configuration must be in VTP server mode.BThe switches must be in the same VTP domain.CThe switch that will share the VLAN information must be configured as the root bridge.DThe switches must be connected over VLAN trunks.EThe switches must be configured to use the same STP version.FThe switches must have VTP pruning activated.
考题
单选题Switch A is configured with VLAN 105 and 106. Switch Bis configured with VLAN 105 and 107.Both switches are connected with a fiber cable. In order for packets from all VLANs to cross thefiber cable, which of the following configurations MUST be present? ()A
Reverse ARPB
Full duplex on the fiber linkC
PoED
802.1q trunking