网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100. Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）
- A、Bandwidth of 101,500
- B、Bandwidth of about 34,000
- C、Bandwidth of 500
- D、Delay of 1200
- E、Delay of 2010
- F、Delay of 20100
参考答案
更多 “ Router R1 is three router hops away from subnet 10.1.1.0/24. According to various show interfaces commands, all three links between R1 and 10.1.1.0/24 use the following settings: bandwidth: 1000, 500, 100000 and delay : 12000, 8000, 100. Which of the following answers correctly identifies a value that feeds into the EIGRP metric calculation？（）A、Bandwidth of 101,500B、Bandwidth of about 34,000C、Bandwidth of 500D、Delay of 1200E、Delay of 2010F、Delay of 20100” 相关考题
考题
以下是路由器R1的部分配置，请完成其配置，或解释配置命令含义。!R1 (Config) interface fastethernet0R1(Config-if) ip address (6) (7)R1(Config-if) (8) (开启端口)!R1 (Config) interface serial 0R1(Config-if) ip address (9) (10)!R1 (Config) ip routingR1 (Config) router rip (11)R1 (Config-router) (12) (声明网络)R1 (Config-router) (13) (声明网络)R1 (Config-router) (14) (声明网络)R1 (Config-router) version 2 (15)!
考题
一台Cisc0路由器R1的第3模块第1端口通过DDN的E1专线与一台远程路由器R2的第4模块第2端口相连，在R1的端口上封装PPP协议。为R1和R2端口分配的IP地址分别为193．42．91．201/30和193．42．91．202/30。下列R2的端口配置，正确的是（ ）。A.Router（cortfig）#interface s4/2Router（config-if）#bandwidth 2048Router（config-if）#ip address 193．42．91．202 255．255．255．252Router（config-if）#encapsulation PPPRouter（config-if）#exitB.Router（config）#interface a4/2Router（config-if）#bandwidth 2048Router（config-if）#ip address 193．42．91．202 255．255．255．252Router（config-if）#encapsulation PPPRouter（config-if）#exitC.Router（config）#interface s4/2Router（config-if）#bandwidth 2048Router（config-if）#ip address 193．42．91．201 255．255．255．252Router（config-if）#encapsulation hdleRouter（config-if）#exitD.Router（config）#interface a4/2Router（config-if）#bandwidth 2048Router（config-if）#ip address 193．42．91．202 255．255．255．252Router（config-if）#encapsulation hdlcRouter（config-if）#exit
考题
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP.Which of the following answers lists an item that cannot be matched by route map fred?（）A. Subnet numberB. Next - hop router IP address of the routeC. Whether the route is an E1 or E2 routeD. The ro ute‘s tagE. The number of router hops between the router and the subnet
考题
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
考题
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
考题
Based on the show ip route isis output on R1, which statement is true? ()
A. The i su 10.1.0.0/23 route is a suppressed route.B. The i su 10.1. 0.0/23 route is a summary route.C. The i su 10.1.0.0/23 route is an IS - IS external route.D. The R1 IS - IS router is an ASBR.E. The R1 IS - IS router is an ABR that belongs to multiple IS - IS areas.F. The R1 IS - IS router is performing route aggregation and is suppressing the more specific 10.1.0.0/23 prefix.
考题
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
考题
Refer to the exhibit. Network 10.0.0.0／8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0／8 network is true? ()
A. Router R2 will be preferred because it has the higher neighbor IP address.B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.C. Router R1 will be preferred because it has a lower local preference.D. Router R2 will be preferred because it has a higher local preference.E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.F. Router R1 will be preferred because it has the lower neighbor IP address.
考题
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 ／26 and 172.16.1.64 ／27. On the basis of the partial output in the exhibit, which statement is true? ()
A. Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.B. Router R1 will advertise both rou tes.C. Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.D. Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
考题
A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。A.The router will use the static route.B.The router will use the OSPF route.C.The router will use the EIGRP route.D.The router will load balance and use all three routes.
考题
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this？ （）A、 en standby preemptB、 standby preempt enableC、 standby preemptD、 hot standby preempt
考题
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
考题
Examine the following excerpt from the show ip ospf database asbr -summary command on router R1 (RID 1.1.1.1). Which answer can be verified as definitely true based on this output?（） LS Type: Summary Links (AS Boundary Router) Link State ID: 9.9.9.9 (AS Boundary Router address) Advertising Router: 3.3.3.3 LS Seq Number: 8000000D Checksum: 0xE43A Length: 28 Network Mask: /0 TOS: 0 Metric: 100A、The output describes the contents of a Type 5 LSAB、3.3.3.3 identifies a ro uter as being the router performing redistributionC、R1's metric for its best route to reach the router with RID 9.9.9.9 is 100D、The router with RID 3.3.3.3's metric for its best route to reach the router with RID 9.9.9.9 is 100
考题
A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。A、The router will use the static route.B、The router will use the OSPF route.C、The router will use the EIGRP route.D、The router will load balance and use all three routes.
考题
Which three statements about the secure domain router are true？（）A、The logical router can span across chassis.B、The fabric and system controller module are shared by all logical routers.C、Each logical router has a distinct fabric and system controller moduleD、The logical router can share a route processorE、The logical router cannot share a route processor
考题
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）A、Subnet numberB、Next - hop router IP address of the routeC、Whether the route is an E1 or E2 routeD、The ro ute's tagE、The number of router hops between the router and the subnet
考题
Router R1 needs to be configured to advertise a specific network. Which of the followingcommands would you use if you wanted to advertise the subnet 154.2.1.0 255.255.255.0 to the EBGP neighbors on your subnet？（）A、Router （config-router）#network 154.2.1.0B、outer （config-router）#network 164.2.1.0C、Router （config-router）#network-advertise 154.2.1.0D、Router （config-router）#network 154.2.1.0 mask 255.255.255.0E、None of the other alternatives apply
考题
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
考题
A router has been configured with an EIGRP variance of 3. Which of the following statements istrue？（）A、An error will result because a router cannot be configured with an EIGRP variance of 3 becausethe maximum variance number is 2B、The successor route will end up in the routing table， and so will any route with a metric at mostthree times greater than the value of the successor’s metricC、EIGRP will only advertise routes that are within three hops of the current routerD、The successor route will end up in the routing table， and so will any route with a metric at leastone third the value of the successor’s metricE、The best three routes with equal cost paths will end up in the routing tableF、The successor route will be any route with three times the value of the advertised distance
考题
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
考题
Three IS-IS routers on a broadcast segment have different priority values configured. Which router is elected the DIS on that broadcast segment?（）A、the router with the lowest priorityB、the router with the highest priorityC、the router with the highest System IDD、the router with the highest IP address
考题
单选题Three IS-IS routers on a broadcast segment have different priority values configured. Which router is elected the DIS on that broadcast segment?（）A
the router with the lowest priorityB
the router with the highest priorityC
the router with the highest System IDD
the router with the highest IP address
考题
多选题On router R1， which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command？（）ABOOTPBTFTPCARPDDNSEproxy-ARPFFTPGCDP
考题
单选题There are three IS-IS routers on a Gigabit Ethernet segment: Router A, Router B, and Router C. Each router is configured in the same area and each routers Gigabit Ethernet interface is configured for Level 1-only. Router A is the Designated Intermediate System (DIS). Each routers IP address on that segment is: Router A: 10.1.1.1/24 Router B: 10.1.1.2/24 Router C: 10.2.2.1/26 Which statement is true about all the adjacencies that exist on that LAN?（）A
No routers are adjacent with each other.B
Only Router A and Router B are adjacent at Level 1.C
Only Router A and Router B are adjacent at Level 2.D
All three routers are adjacent with each other at Level 1.
考题
单选题Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）A
Subnet numberB
Next - hop router IP address of the routeC
Whether the route is an E1 or E2 routeD
The ro ute's tagE
The number of router hops between the router and the subnet
考题
多选题Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）AInitBIdleCActiveDStandbyEEstablishedFBackup
热门标签
最新试卷