多选题On router R1， which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command？（）ABOOTPBTFTPCARPDDNSEproxy-ARPFFTPGCDP

考题 Given the following MPLS L2 configuration command:mpls－relay 10.1.1.1 4Which two statements true? ()(Choose two.) A. This command is applied to the core router facing interface.B. This command is applied to the customer facing interface.C. The 4 is locally significant and identifies the layer 2 circuit.D. The 4 must match exactly on the peer router configuration on the remote end.

查看答案

考题 Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0A. OSPF works on F0/0 and S0/0/0 without further configurationB. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modEC. OSPF works with the addition of one command: an router - id command in OSPF router configuration modED. OSPFv3 needs at least two more configuration commands before it works on R1

查看答案

考题 Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: Gateway of last resort is 1.1.1.1 to network 2.0.0.0.Whic h of the following is most likely to have caused this output to occur on R1?（）A. R1 has been configured with an ip default- network 2.0.0.0 command.B. R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C. R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D. Another router has been configured with an ip default - network 2.0.0.0 command.E. Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.

查看答案

考题 Which three of the following protocols will be forwarded to a host specified by the ip helper - address interface configuration command if the configuration has not been modified by the ip forward - protocol udp global con figuration command?（）A. BOOTPB. TFTPC. ARPD. DNSE. proxy - ARPF. FTP

查看答案

考题 Refer to the exhibit. Which statement is co rrect regarding the router configuration shown? () A. The router will rebroadcast any DHCP requests received by this interface out to all interfaces included in the ip helper - address commands.B. The router will rebroadcast any UDP broadcasts received by this interface out to all interfaces included in the ip helper - address commands.C. The router will unicast any DHCP requests received by this interface out to all addresses included in the ip helper - address commands.D. This configuration will not do anything because the ip helper - address command needs to also be applied to the 192.168.23.1 IP address.

查看答案

考题 Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

查看答案

考题 Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1‘s (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode.Which of the following occurs？（）A.Fa0/0 failsB.The command is rejecteDC.The existing three neighbors failD.The neighborship with 172.16.2.20 fails and then reestablishesE.None of the other answers is correct

查看答案

考题 A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with:Would you like to enter the initial configuration dialog? [yes/no]Why has this occurred?（）A. There is an error in the router DRAM.B. Te IOS image is corrupt.C. The configuration register is set to 0x2142.D. The TFTP server that contains the router configuration file is unreachable.E. A boot system configuration command has placed the router into setup mode.

查看答案

考题 The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?() A. The default administrative distance is used.B. The command is used to establish a static route.C. The command is used to configure the router interfaces.D. The command is used to establish a stub network.E. The subnet mask for the source address is 255.255.255.0

查看答案

考题 The command frame－relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command()。 A.This command should be executed from the global configuration modeB.The IP address 10.121.16.8 is the local router port used to forward dataC.102 is the remote DLCI that will receive the informationD.This command is required for all Frame Relay configurationsE.The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC

查看答案

考题 The VLANs in switch R1 are being modified. Which of the following are updated in R1 every time a VLAN is modified？（）A、Configuration revision numberB、Configuration revision flag fieldC、Configuration revision reset switchD、Configuration revision databaseE、None of the other alternatives apply

查看答案

考题 On router R1， which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command？（）A、BOOTPB、TFTPC、ARPD、DNSE、proxy-ARPF、FTPG、CDP

查看答案

考题 The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A、An a uto - cost reference - bandwidth 1000 command in router ospf modeB、An auto - cost reference - bandwidth 2000 command in router ospf modeC、An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD、An auto - cost reference - bandwidth 64700 command i n router ospf mode

查看答案

考题 The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command？（）A、This command should be executed from the global configuration mode.B、The IP address 10.121.16.8 is the local router port used to forward data.C、102 is the remote DLCI that will receive the information.D、This command is required for all Frame Relay configurations.E、The broadcast option allows packets， such as RIP updates， to be forwarded across the PVC

查看答案

考题 Which three of the following protocols will be forwarded to a host specified by the ip helper - address interface configuration command if the configuration has not been modified by the ip forward - protocol udp global con figuration command?（）A、BOOTPB、TFTPC、ARPD、DNSE、proxy - ARPF、FTP

查看答案

考题 Which of the following should an administrator do after running a command from the console onthe perimeter router?（）A、Update the configuration logsB、Update the network wiring schematicsC、Update the network configuration proceduresD、Compare the configuration with the baseline

查看答案

考题 Which Control Plane Policing （CoPP） statement is true？（）A、 Traffic to be policed is identified using the control-plane global configuration command.B、 The control-plane global configuration command enters the Cisco Modular QoS CLI （MQC） mode.C、 The control-plane global configuration command enters the control-plane configuration mode. D、 Traffic to be policed is identified using the control-plane interface configuration command.E、 The control-plane interface configuration command enters the Cisco Modular QoS CLI （MQC） mode.F、 The control-plane interface configuration command enters the control-plane configuration mode.

查看答案

考题 Which statement about PPPoA configuration is correct？（）A、The dsl operating-mode auto command is required if the default mode has been changedB、The ip mtu 1496 command must be applied on the dialer interfaceC、The encapsulation ppp command is requiredD、The ip mtu 1492 command must be applied on the dialer interface

查看答案

考题 The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?（）A、The default administrative distance is used.B、The command is used to establish a static route.C、The command is used to configure the router interfaces.D、The command is used to establish a stub network.E、The subnet mask for the source address is 255.255.255.0

查看答案

考题 The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command（）。A、This command should be executed from the global configuration modeB、The IP address 10.121.16.8 is the local router port used to forward dataC、102 is the remote DLCI that will receive the informationD、This command is required for all Frame Relay configurationsE、The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC

查看答案

考题 Given the following MPLS L2 configuration command: mpls-relay 10.1.1.1 4 Which two statements true? （）(Choose two.)A、This command is applied to the core router facing interface.B、This command is applied to the customer facing interface.C、The 4 is locally significant and identifies the layer 2 circuit.D、The 4 must match exactly on the peer router configuration on the remote end.

查看答案

考题多选题On router R1， which three of the following protocols will be forwarded to a host specified by the "iphelper-address" interface configuration command if the configuration has not been modified by the"ip forward-protocol udp" global configuration command？（）ABOOTPBTFTPCARPDDNSEproxy-ARPFFTPGCDP

查看答案

考题多选题Given the following MPLS L2 configuration command: mpls-relay 10.1.1.1 4 Which two statements true? （）(Choose two.)AThis command is applied to the core router facing interface.BThis command is applied to the customer facing interface.CThe 4 is locally significant and identifies the layer 2 circuit.DThe 4 must match exactly on the peer router configuration on the remote end.

查看答案

考题多选题Which three of the following protocols will be forwarded to a host specified by the ip helper - address interface configuration command if the configuration has not been modified by the ip forward - protocol udp global con figuration command?（）ABOOTPBTFTPCARPDDNSEproxy - ARPFFTP

查看答案

考题单选题The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command？（）A This command should be executed from the global configuration mode.B The IP address 10.121.16.8 is the local router port used to forward data.C 102 is the remote DLCI that will receive the information.D This command is required for all Frame Relay configurations.E The broadcast option allows packets， such as RIP updates， to be forwarded across the PVC

查看答案

考题多选题The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1AAn a uto - cost reference - bandwidth 1000 command in router ospf modeBAn auto - cost reference - bandwidth 2000 command in router ospf modeCAn ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeDAn auto - cost reference - bandwidth 64700 command i n router ospf mode

查看答案

考题单选题Which statement about PPPoA configuration is correct？（）A The dsl operating-mode auto command is required if the default mode has been changedB The ip mtu 1496 command must be applied on the dialer interfaceC The encapsulation ppp command is requiredD The ip mtu 1492 command must be applied on the dialer interface

查看答案

考题多选题The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?（）AThe default administrative distance is used.BThe command is used to establish a static route.CThe command is used to configure the router interfaces.DThe command is used to establish a stub network.EThe subnet mask for the source address is 255.255.255.0

查看答案

网友您好， 请在下方输入框内输入要搜索的题目：

网友您好，请在下方输入框内输入要搜索的题目：