网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（） router ospf 1 redistribute ospf 2 external 2 route - map fred ! route - map fred permit 10 match ip address 1 set metric - type type - 1
- A、No routes are redistributed because a route cannot be both E1 and E2.
- B、Only OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.
- C、Inside the OSPF 2 domain, any formerly E2 routes will become E1 routes.
- D、Routes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
参考答案
更多 “ Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（） router ospf 1 redistribute ospf 2 external 2 route - map fred ! route - map fred permit 10 match ip address 1 set metric - type type - 1A、No routes are redistributed because a route cannot be both E1 and E2.B、Only OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.C、Inside the OSPF 2 domain, any formerly E2 routes will become E1 routes.D、Routes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.” 相关考题
考题
【问题2】（6 分）根据网络拓扑和需求说明，完成路由器R1的配置。R1(config)# interface Serial 1/0R1(config-if)# ip address （3） 255.255.255.0 （设置串口地址）R1(config-if)#no shutdown （开启串口）R1(config)#interface FastEthernet0/0R1(config-if)#ip address （4） 255.255.255.0 （设置以太口地址）R1(config-if)#exitR1(config)#router ospf 1R1(config-router)#network 192.0.0.1 （5） area 0R1(config-router)#network 192.1.1.1 （6） area 0
考题
以下是路由器R1的部分配置，请完成其配置，或解释配置命令含义。!R1 (Config) interface fastethernet0R1(Config-if) ip address (6) (7)R1(Config-if) (8) (开启端口)!R1 (Config) interface serial 0R1(Config-if) ip address (9) (10)!R1 (Config) ip routingR1 (Config) router rip (11)R1 (Config-router) (12) (声明网络)R1 (Config-router) (13) (声明网络)R1 (Config-router) (14) (声明网络)R1 (Config-router) version 2 (15)!
考题
What type of OSPF router is responsible for redistributing routes into OSPF?()
A. ABRB. ASBRC. internal routerD. backbone router
考题
Router R1 sets a route tag for subnet 10.1.1.0／24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?()
A. Kilobits/seconDB. Tens of microsecondsC. CostD. Hop countE. No unit is assigneD
考题
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
考题
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
考题
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
考题
Based on the show ip route isis output on R1, which statement is true? ()
A. The i su 10.1.0.0/23 route is a suppressed route.B. The i su 10.1. 0.0/23 route is a summary route.C. The i su 10.1.0.0/23 route is an IS - IS external route.D. The R1 IS - IS router is an ASBR.E. The R1 IS - IS router is an ABR that belongs to multiple IS - IS areas.F. The R1 IS - IS router is performing route aggregation and is suppressing the more specific 10.1.0.0/23 prefix.
考题
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
考题
Refer to the exhibit. Network 10.0.0.0／8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0／8 network is true? ()
A. Router R2 will be preferred because it has the higher neighbor IP address.B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.C. Router R1 will be preferred because it has a lower local preference.D. Router R2 will be preferred because it has a higher local preference.E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.F. Router R1 will be preferred because it has the lower neighbor IP address.
考题
Refer to the exhibit. EIGRP is configured on all routers in the network. On a basis of the show ip eigrp topology output provided, what conclusion can be deri ved? ()
A.Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring for a second successor to network 10.6.1.0/24B.Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0C.Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out before it declares the neighbor unreachableD.Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent out about network 10 .6.1.0/24
考题
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 ／26 and 172.16.1.64 ／27. On the basis of the partial output in the exhibit, which statement is true? ()
A. Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.B. Router R1 will advertise both rou tes.C. Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.D. Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
考题
Whichseriesofcommands willconfigurerouterR1forLAN－to－LANcommunicationwithrouterR2?Theenterprisenetworkaddressis192.1.1.0／24andtheroutingprotocolinuseisRIP.()
A.R1（config）#interfaceethernet0；R1（config-if）#ipaddress192.1.1.129255.255.255.192；R1（config-if）#noshutdownB.R1（config）#interfaceethernet0；R1（config-if）#ipaddress192.1.1.97255.255.255.192；R1（config-if）#noshutdownC.R1（config）#interfaceserial0；R1（config-if）#ipaddress192.1.1.4255.255.255.252；R1（config-if）#clockrate56000D.R1（config）#interfaceserial0；R1（config-if）#ipaddress192.1.1.6255.255.255.252；R1（config-if）#noshutdownE.R1（config）#routerrip；R1（config-router）#network192.1.1.4；R1（config-router）#network192.1.1.128F.R1（config）#routerrip；R1（config-router）#version2；R1（config-router）#network192.1.1.0
考题
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
考题
In which Cisco IOS configuration mode is the route distinguisher （RD） configured？（）A、R1（config-route-at）#B、R1（config-route-map）#C、R1（config-it）#D、R1（config-vrf）#E、R1（config）#F、R1（router）#
考题
Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）A、 InitB、 IdleC、 ActiveD、 StandbyE、 EstablishedF、 Backup
考题
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
考题
What must be configured on the network in order for users on the Internet to view web pages located on Web Server 2?（）A、On router R2， configure a default static route to the 192.168.1.0 network.B、On router R2， configure DNS to resolve the URL assigned to Web Server 2 to the 192.168.1.10 address.C、On router R1， configure NAT to translate an address on the 209.165.100.0/24 network to 192.168.1.10.D、On router R1， configure DHCP to assign a registered IP address on the 209.165.100.0/24 network to Web Server 2.
考题
Router R1 sits inside OSPF area 1. Router R2 redistributes an E1 route into OSPF for prefix 2.2.2.0/24, with external metric 20. Router R22 redistributes an E2 route for the same prefix/length, external metric 10. Under what conditions will R1 choose as it s best route the route through R22?（）A、R1 will always choose the route through R22.B、As long as R1's best internal OSPF cost to reach R22 is less than 10.C、As long as R1's best internal OSPF cost to reach R22 is less than 20.D、R1 will never choo se the route through R22 if the E1 route through R2 is available.
考题
Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（） route - map fred deny 10 match ip address one route - map fred deny 20 match ip address two route - map fred permit 100A、The third route map clause will allow any routes not already filtered by the first two clausesB、R outes permitted by ACL "two" will be redistributedC、Routes denied by ACL "one" will be redistributedD、All routes will be filtereD
考题
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
考题
单选题What type of OSPF router is responsible for redistributing routes into OSPF?（）A
ABRB
ASBRC
internal routerD
backbone router
考题
单选题Which router is doing LSA type 7 to type 5 translation，and why？（）A
Both RTA and RTB will do LSA7/5 translation，since they are both NSSA ABRsB
RTA will do LSA7/5 translation，since it has the lower router IDC
RTB will do LSA7/5 translation，since it has the higher router IDD
The redistributing router will do LSA7/5 translation，since it is within the NSSA
考题
单选题Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）A
Kilobits/seconDB
Tens of microsecondsC
CostD
Hop countE
No unit is assigneD
考题
多选题Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）AReceive - onlyBStubCStaticDSummaryEConnectedFDynamic
考题
多选题On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）Ashow ip routeBshow ip eigrp topologyCshow ip ospf topologyDshow ip eigrp topology 10.1.1.0/24
考题
多选题Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）AInitBIdleCActiveDStandbyEEstablishedFBackup
热门标签
最新试卷