网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）
A.Check and change the access lists on router RTA
B.Configure the auto summary command under router eigrp 1 on router RTA
C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface
D.Issue the no ip split horizon command on router RTA
E.Issue the no ip split horizon eigrp 1 command on router RTA
F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers
参考答案
更多 “ Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）A.Check and change the access lists on router RTAB.Configure the auto summary command under router eigrp 1 on router RTAC.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterfaceD.Issue the no ip split horizon command on router RTAE.Issue the no ip split horizon eigrp 1 command on router RTAF.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers ” 相关考题
考题
Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? ()
A. area 0 stub o n routers R4 and R5B. area 5 stub on routers R4 and R5C. area 5 stub no - summary on routers R4 and R5D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5E. area 5 stub no - summary on router R4 and area 5 stub on router R5
考题
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()
A. Issue the command bandwidth 224 on the physical interface.B. Issue the command bandwidth 56 on the physical interface.C. Issue the command bandwidth 224 on each subinterface.D. Issue the command bandwidth 56 on each subinterface.
考题
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）A. Add the area 1 stub command on routers R1.B. Add the always keyword to the default - information originate configuration command on router R2.C. Remov e the default information originate configuration command from router R2 and place it on router R1.D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
考题
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
考题
Refer to the exhibit. In a redundant hub - and - spoke deployment using EIGRP, what feature can be used to ensure that routers C through F are not used as transit routers for data traveling from router B to network 10.1.1.0? Select the best response.（）A. Use address summarization at routers C, D, E, and FB. Use the EIGRP Stub featu re on routers C, D, E, and FC. Use passive - interface on the spoke links in routers A and BD. Change the administrative distance in routers A and B for routes learned from routers C, D, E,and F
考题
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
考题
Refer to the exhibit. You are the network administrator of the Route.com company. You have been tasked to implement a hub and spoke EIGRP topology over Frame Relay to provide connectivity between the networks at headquarters and all 300 spokes. Before you begin the actual implementation, which three pieces of information are more important to know than the others?（）A. the Committed Information Rate of all the Frame Relay PVCsB. the Cisco IOS version running on all the routersC. the router model number of all the spoke routersD. the number of HQ networks connected behind the headquarter routersE. the routing policy, such as whether or not the spokes can be used as backup transient point between the two headquarter routers
考题
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
考题
Refer to the exhibit. Routers RTA and RTB are running BGP but the session is active. What command needs to be added to esta blish the BGP session? ()
A. ip route 10.10.10.1 255.255.255.255 s0/0 ip route 10.10.10.1 255.255.255.255 s0/1B. network 10.10.10.0C. no synchronizationD. neighbor 10.10.10.1 next - hop - self
考题
Refer to the exhibit. By default, when RTB passes BGP advertisements from RTA about network 192.168.2.0 to RTC, what address will be listed as the next － hop address? ()
A. 10.1.1.2B. 192.168.1.49C. 10.1.1.1D. 192.168.1.50
考题
Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200?()
A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5B. None of the BGP updates that are received on router R2 will ever be received by router R5C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4D. All BGP updates that are received on router R2 will be sent directly to router R5
考题
Refer to the exhibit. Which st atement is true?()
A. Router RTA is the BDRB. Router RTA is directly connected to interface 192.168.45.1C. Neighbor 192.168.45.1 has changed its OSPF priority numberD. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs
考题
Refer to the exhibit. Which statement is true about the configuration? ()
A. RTA will not establish an OSPF adjacency w ith RTBB. RTA will send OSPF hello packets, but will not send OSPF updatesC. RTA will not accept OSPF hello packets from RTBD. RTA will send OSPF updates, but will not establish an adjacency with RTB
考题
Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.Which two EIGRP routes will be seen in the routing table of router R3?（）A. 10.0.0.0/8B. 172.16.10.0/24C. 172.16.0.0/24D. 10.10.10.0/24E. 172.16.0.0/16F. 10.10.0.0/16
考题
Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B?()
A.The loopback addresses are on different subnetsB.The value of the dead timers on the router are differentC.Route summarization is enabled on both routersD.The process indentifier on router A is different than the process identifier on router B
考题
Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? ()
A.Router1 has specific boot system command that instruct it to load IOS from TFTP server.B.Router1 is acting as a TFTP server for other routers.C.Router1 cannot locate a valid IOS image in flash memory.D.Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.E.Cisco routers will first attempt to load a image from TFTP for management purposes.
考题
RTA的Serial0接口和RTB的Serial0接口通过一条点到点链路相连，此链路上运行PPP协议，RTA的Serial0接口配置IP地址为10.1.1.1/30，RTB的Serial接口配置IP地址为10.1.1.2/30；关于RTA产生的Router-LSA，以下说法正确的是（）。A、RTA产生两条Router-LSA，每条Router-LSA使用一条Link ID描述这条链路B、RTA产生两条Router-LSA，每条Router-LSA使用两条Link ID描述这条链路C、RTA产生一条Router-LSA，此Router-LSA中只使用一条Link ID描述这条链路D、RTA产生一条Router-LSA，此Router-LSA中使用两条Link ID描述这条链路
考题
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A、As numbers must be changed to match on all the routers.B、Loopback interface must be configured so a DR is elected.C、The no auto-summary command is needed on Router A and Router C.D、Router B needs to have two network statements, one for each connected network.
考题
A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）A、The central site router has 100 fully adjacent neighborships with the 100 branchesB、The central site router has neighborships with all branch routers, but fully adjacent neighbors with only two branchesC、The central site router has a neighborship with the Frame Relay switcHD、None of the other answers is correct
考题
Which router is doing LSA type 7 to type 5 translation，and why？（）A、Both RTA and RTB will do LSA7/5 translation，since they are both NSSA ABRsB、RTA will do LSA7/5 translation，since it has the lower router IDC、RTB will do LSA7/5 translation，since it has the higher router IDD、The redistributing router will do LSA7/5 translation，since it is within the NSSA
考题
两台路由器RTA、RTB的串口Ｓ0用一条链路连接，链路协议位PPP，两各接口的网络类型均为point-to-point，此时接口与链路均为UP，配置该网段： RTA（config-if-serial0）#ipaddress 10.10.10.1 255.255.0.0； RTA（config-router-ospf）#network 10.10.10.10.0.0.0area 1； RTB（config-if-serial0）#ipaddress 10.10.10.2 255.255.255.0； RTB（config-router-ospf）#network 10.10.10.20.0.0.0area 1； RTA（config）#showipospfneighbour RTA邻居状态机最终状态（）A、FULLB、DOWNC、TWOWAYD、ATTEMP
考题
Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）A、 Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.B、 This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.C、 The router at RemoteB must be replaced by a Cisco router.D、 Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.E、 There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.
考题
What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）A、A hub router prevents routes from being advertised to the remote router.B、Only remote routers are configured as stubs.C、Stub routers are not queried for routes.D、Spoke routers connected to hub routers answer the route queries for the stub router.E、A stub router should have only EIGRP hub routers as neighbors.F、EIGRP stub routing should be used on hub routers only.
考题
Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）A、Router1 has specific boot system command that instruct it to load IOS from TFTP server.B、Router1 is acting as a TFTP server for other routers.C、Router1 cannot locate a valid IOS image in flash memory.D、Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.E、Cisco routers will first attempt to load a image from TFTP for management purposes.
考题
单选题Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?（）A
10.1.1.2B
10.154.154.1C
172.16.5.1D
192.168.5.3
考题
单选题Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A
As numbers must be changed to match on all the routers.B
Loopback interface must be configured so a DR is elected.C
The no auto-summary command is needed on Router A and Router C.D
Router B needs to have two network statements, one for each connected network.
考题
单选题Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）A
Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.B
This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.C
The router at RemoteB must be replaced by a Cisco router.D
Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.E
There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.
热门标签
最新试卷